Texas Instruments LM628N-8
- Part Number:
- LM628N-8
- Manufacturer:
- Texas Instruments
- Ventron No:
- 3741807-LM628N-8
- Description:
- IC MOTOR CONTROLLER PAR 28DIP
- Datasheet:
- LM628/LM629
Texas Instruments LM628N-8 technical specifications, attributes, parameters and parts with similar specifications to Texas Instruments LM628N-8.
- MountSurface Mount, Through Hole
- Mounting TypeThrough Hole
- Package / Case28-DIP (0.600, 15.24mm)
- Number of Pins28
- Operating Temperature-40°C~85°C TA
- PackagingTube
- JESD-609 Codee0
- Part StatusObsolete
- Moisture Sensitivity Level (MSL)1 (Unlimited)
- Number of Terminations28
- ECCN CodeEAR99
- Terminal FinishTin/Lead (Sn/Pb)
- ApplicationsGeneral Purpose
- SubcategoryMotion Control Electronics
- TechnologyNMOS
- Voltage - Supply4.5V~5.5V
- Terminal PositionDUAL
- Peak Reflow Temperature (Cel)260
- Supply Voltage5V
- Terminal Pitch2.54mm
- Reflow Temperature-Max (s)40
- Base Part NumberLM628
- FunctionController - Commutation, Direction Management
- Number of Outputs1
- Supply Voltage-Max (Vsup)5.5V
- Power Supplies5V
- Supply Voltage-Min (Vsup)4.5V
- InterfaceParallel
- Analog IC - Other TypeBRUSH DC MOTOR CONTROLLER
- Output ConfigurationPre-Driver - Half Bridge (4)
- Motor Type - AC, DCBrushless DC (BLDC) Servo, Brushed DC Servo
- Height4.19mm
- Length36.07mm
- Width12.95mm
- Radiation HardeningNo
- RoHS StatusNon-RoHS Compliant
- Lead FreeContains Lead
LM628N-8 Overview
The mounting type for this particular component is through hole, meaning it can be securely attached to a circuit board using traditional methods. Its operating temperature range is quite wide, from -40°C to 85°C TA, making it suitable for a variety of environments. However, this part is now considered obsolete, which means it may be difficult to find and may not be supported by the manufacturer. The terminal finish is tin/lead (Sn/Pb), and the voltage supply range is 4.5V to 5.5V. The terminal position is dual, and the terminal pitch is 2.54mm. The maximum reflow temperature for this component is 40 seconds. It requires a 5V power supply and has a pre-driver half bridge output configuration with four pins.
LM628N-8 Features
Applications : General Purpose
base on LM628 number
designed with 1 outputs
LM628N-8 Applications
There are a lot of Texas Instruments LM628N-8 motor drivers applications.
Indicator circuit
Street lights
Multiple output capability
Large outdoor LED display
Handheld devices
Home lighting systems
Lighting for health and wellbeing
Display LED backlighting
Fog lamps
Smart lighting applications
The mounting type for this particular component is through hole, meaning it can be securely attached to a circuit board using traditional methods. Its operating temperature range is quite wide, from -40°C to 85°C TA, making it suitable for a variety of environments. However, this part is now considered obsolete, which means it may be difficult to find and may not be supported by the manufacturer. The terminal finish is tin/lead (Sn/Pb), and the voltage supply range is 4.5V to 5.5V. The terminal position is dual, and the terminal pitch is 2.54mm. The maximum reflow temperature for this component is 40 seconds. It requires a 5V power supply and has a pre-driver half bridge output configuration with four pins.
LM628N-8 Features
Applications : General Purpose
base on LM628 number
designed with 1 outputs
LM628N-8 Applications
There are a lot of Texas Instruments LM628N-8 motor drivers applications.
Indicator circuit
Street lights
Multiple output capability
Large outdoor LED display
Handheld devices
Home lighting systems
Lighting for health and wellbeing
Display LED backlighting
Fog lamps
Smart lighting applications
LM628N-8 More Descriptions
LM628/LM629 Precision Motion Controller | IC MOTOR DRIVER 4.5V-5.5V 28DIP
Precision Motion Controller 28-PDIP -40 to 85
NMOS Tube LM628 General Purpose motor controller 5V 12.95mm -40C~85C TA
Precision Motor Controller 28-Pin PDIP Rail
Brush DC Motor Controller, NMOS, PDIP28
IC SUPERVISOR 1 CHANNEL SOT23-5
Ic,Motor Controller,Mos,Dip,28Pin
The LM628/LM629 are dedicated motion-control processors designed for use with a variety of DC and brush less DC servo motors, and other servomechanisms which provide a quadrature incremental position feedback signal. The parts perform the intensive, real-time computational tasks required for high performance digital motion control. The host control software interface is facilitated by a high-level command set. The LM628 has an 8-bit output which can drive either an 8-bit or a 12-bit DAC. The components required to build a servo system are reduced to the DC motor/actuator, an incremental encoder, a DAC, a power amplifier, and the LM628. An LM629-based system is similar, except that it provides an 8-bit PWM output for directly driving H-switches. The parts are fabricated in NMOS and packaged in a 28-pin dual in-line package or a 24-pin surface mount package (LM629 only). Both 6 MHz and 8 MHz maximum frequency versions are available with the suffixes -6 and -8, respectively, used to designate the versions. They incorporate an SDA core processor and cells designed by SDA.
Precision Motion Controller 28-PDIP -40 to 85
NMOS Tube LM628 General Purpose motor controller 5V 12.95mm -40C~85C TA
Precision Motor Controller 28-Pin PDIP Rail
Brush DC Motor Controller, NMOS, PDIP28
IC SUPERVISOR 1 CHANNEL SOT23-5
Ic,Motor Controller,Mos,Dip,28Pin
The LM628/LM629 are dedicated motion-control processors designed for use with a variety of DC and brush less DC servo motors, and other servomechanisms which provide a quadrature incremental position feedback signal. The parts perform the intensive, real-time computational tasks required for high performance digital motion control. The host control software interface is facilitated by a high-level command set. The LM628 has an 8-bit output which can drive either an 8-bit or a 12-bit DAC. The components required to build a servo system are reduced to the DC motor/actuator, an incremental encoder, a DAC, a power amplifier, and the LM628. An LM629-based system is similar, except that it provides an 8-bit PWM output for directly driving H-switches. The parts are fabricated in NMOS and packaged in a 28-pin dual in-line package or a 24-pin surface mount package (LM629 only). Both 6 MHz and 8 MHz maximum frequency versions are available with the suffixes -6 and -8, respectively, used to designate the versions. They incorporate an SDA core processor and cells designed by SDA.
Popular Search Part Number
Related Keywords
Search Tags
Latest News
-
06 September 2023
All You Need to Know About MPS2222A
Ⅰ. Overview of MPS2222AMPS2222A is an NPN transistor produced by Fairchild Semiconductor. Its main features include power dissipation of 0.625W; collector current of 0.6A; maximum withstand voltage of... -
06 September 2023
A4988 Characteristics, Application and Basic Principle
A4988 is an efficient and commonly used stepper motor driver chip, widely used in 3D printing and CNC machine tools and other fields. We will discuss in depth... -
07 September 2023
What Is The Difference Between NE5532 And RC4558D?
Ⅰ. Overview of NE5532NE5532 is a dual operational amplifier chip with excellent performance and low noise characteristics. Its circuit design is similar to that of a common operational... -
07 September 2023
TPC8129 Internal Circuit, Specifications, Application and Marking
Ⅰ. Overview of TPC8129TPC8129 is a product of Toshiba, a Japanese comprehensive electronic and electrical company. It is a chip for LED driver circuits and is mainly used...
Help you to save your cost and time.
Reliable package for your goods.
Fast Reliable Delivery to save time.
Quality premium after-sale service.