Home > Products > Integrated Circuits (ICs) > Interface - Analog Switches, Multiplexers, Demultiplexers > MAX312CPE
MAX312CPE

Maxim Integrated MAX312CPE

Part Number:
MAX312CPE
Manufacturer:
Maxim Integrated
Ventron No:
3670553-MAX312CPE
Description:
IC SWITCH QUAD SPST 16DIP
ECAD Model:
Datasheet:
MAX312CPE

Quick Request Quote

Please send RFQ , We will respond immediately.

Part Number
Quantity
Company
E-mail
Phone
Comments
Specifications
Maxim Integrated MAX312CPE technical specifications, attributes, parameters and parts with similar specifications to Maxim Integrated MAX312CPE .
  • Factory Lead Time
    6 Weeks
  • Mount
    Through Hole
  • Mounting Type
    Through Hole
  • Package / Case
    16-DIP (0.300, 7.62mm)
  • Number of Pins
    16
  • Operating Temperature
    0°C~70°C TA
  • Packaging
    Tube
  • Published
    2002
  • JESD-609 Code
    e0
  • Pbfree Code
    no
  • Part Status
    Active
  • Moisture Sensitivity Level (MSL)
    1 (Unlimited)
  • Number of Terminations
    16
  • Termination
    Through Hole
  • ECCN Code
    EAR99
  • Resistance
    10Ohm
  • Terminal Finish
    Tin/Lead (Sn85Pb15)
  • Subcategory
    Multiplexer or Switches
  • Max Power Dissipation
    842mW
  • Technology
    CMOS
  • Peak Reflow Temperature (Cel)
    240
  • Number of Functions
    4
  • Supply Voltage
    15V
  • Reflow Temperature-Max (s)
    20
  • Base Part Number
    MAX312
  • Output
    SEPARATE OUTPUT
  • Pin Count
    16
  • Operating Supply Voltage
    18V
  • Power Supplies
    512/ -15V
  • Number of Channels
    1
  • Number of Circuits
    4
  • Max Supply Voltage
    30V
  • Min Supply Voltage
    4.5V
  • Nominal Supply Current
    5μA
  • Max Supply Current
    1μA
  • Throw Configuration
    SPST
  • Turn On Delay Time
    275 ns
  • Voltage - Supply, Single/Dual (±)
    4.5V~30V ±4.5V~20V
  • Supply Type
    Dual, Single
  • Neg Supply Voltage-Nom (Vsup)
    -15V
  • Turn-Off Delay Time
    235 ns
  • Max Dual Supply Voltage
    20V
  • On-State Resistance (Max)
    10Ohm
  • Min Dual Supply Voltage
    4.5V
  • Dual Supply Voltage
    9V
  • Multiplexer/Demultiplexer Circuit
    1:1
  • Off-state Isolation-Nom
    65 dB
  • Current - Leakage (IS(off)) (Max)
    500pA
  • Channel Capacitance (CS(off), CD(off))
    15pF 15pF
  • On-state Resistance Match-Nom
    0.3Ohm
  • Switch Circuit
    SPST - NC
  • Switch Time (Ton, Toff) (Max)
    225ns, 185ns
  • Charge Injection
    20pC
  • Channel-to-Channel Matching (ΔRon)
    300m Ω
  • Crosstalk
    -85dB @ 1MHz
  • Switching
    BREAK-BEFORE-MAKE
  • Drain to Source Resistance
    10Ohm
  • Normal Position
    NO
  • Height
    4.45mm
  • Length
    19.43mm
  • Width
    7.87mm
  • Radiation Hardening
    No
  • REACH SVHC
    Unknown
  • RoHS Status
    ROHS3 Compliant
  • Lead Free
    Lead Free
Description
MAX312CPE Overview
As the electronic part is packed in 16-DIP (0.300, 7.62mm), international shipping is convenient. This high-reliability packaging method uses advanced packaging methods Tube. Through Hole is where this multiplexer is located. Multiplexers and demultiplexers have a number of circuits 1:1. Operating temperature extended to 0°C~70°C TA. A total of 16 terminations have been recorded. This electronic part offers high-quality output due to its 1 channels. When the electronic component is given a voltage of 15V, it should be turned on and run. It is part of the design of the 16 series that this electronic component is included. Circuits based on SPST - NC switching are used to construct these analog switch ics. There are 4 circuits in this switch device. Try searching with MAX312 if you're looking for variants. It has an internal resistance of 10Ohm. To find out what the functions of 16 pins are, please refer to their datasheets. The analog multiplexer shown here is a typical Multiplexer or Switches. Multiplexers should not be powered above 30V in normal situations. An effective Dual, Single supply digital multiplexer. 4.5V is the lowest voltage the electrical component should receive. A voltage higher than 1μA may cause damage to the switch multiplexer. Despite this switch's dual supply capability, its voltage should not exceed 20V. A dual power supply should have at least 4.5V voltage attached. This analog switch ic utilizes SEPARATE OUTPUT output. It can operate from 18V operating voltages. There is 10Ohm resistance between the Drain and Source on this part.

MAX312CPE Features
1 Channels
Switch Circuit: SPST - NC
Drain-to-Source resistance: 10Ohm

MAX312CPE Applications
There are a lot of Maxim Integrated MAX312CPE Analog Switches & Multiplexers ICs applications.

Audio and video signal routing
CSU
Precision data acquisition
Mechanical reed relay replacement
Precision test equipment
Video signal routing
High reliability control systems
PBX interfaces
Avionics
Medical systems
MAX312CPE More Descriptions
MAXIM INTEGRATED PRODUCTS MAX312CPE IC, SWITCH, QUAD SPST, DIP16, 312
10Ω, Quad, SPST, CMOS Analog Switches
Analog Switch Quad SPST 16-Pin PDIP N
4xSPST Analog Switch <10R DIP16
IC SWITCH SPST-NCX4 10OHM 16DIP
French Electronic Distributor since 1988
SWITCH, QUAD SPST, DIP16, 312; Switch Type, Analogue:SPST; Switches, No. of:4; Voltage, Supply Source:Dual; Resistance, On State:6.5ohm; Voltage, Supply Min:4.5V; Voltage, Supply Max:20V; Termination Type:Through Hole; Case Style:DIP; No. of Pins:16; Operating Temperature Range:0°C to 70°C; Base Number:312; IC Generic Number:312; Logic Function Number:312; No. of Channels:4; Resistance, Rds On:10ohm; Temp, Op. Max:70°C; Temp, Op. Min:0°C; Temperature Range, IC:Commercial
Certification
  • ISO 9001
  • ISO 13485
  • ISO 45001
  • ASA
  • ESD
  • DUNS
  • SMTA
  • ROHS
Popular Search Part Number Related Keywords Search Tags

Latest News

  • cost

    Help you to save your cost and time.

  • package

    Reliable package for your goods.

  • fast

    Fast Reliable Delivery to save time.

  • service

    Quality premium after-sale service.