Honeywell Sensing and Productivity Solutions MA233SAN
- Part Number:
- MA233SAN
- Manufacturer:
- Honeywell Sensing and Productivity Solutions
- Ventron No:
- 4423576-MA233SAN
- Description:
- SENSOR VRS SINE WAVE CONNECTOR
- Datasheet:
- MA233SAN
Honeywell Sensing and Productivity Solutions MA233SAN technical specifications, attributes, parameters and parts with similar specifications to Honeywell Sensing and Productivity Solutions MA233SAN.
- Factory Lead Time8 Weeks
- MountPanel
- Package / CaseBarrel, Stainless Steel
- Number of Pins2
- MaterialStainless Steel
- Weight98g
- Actuator MaterialFerrous Metals, Gear Tooth
- Operating Temperature-55°C~150°C TA
- SeriesMA230
- Published2005
- Part StatusActive
- Moisture Sensitivity Level (MSL)1 (Unlimited)
- TerminationConnector
- Max Operating Temperature150°C
- Min Operating Temperature-55°C
- Frequency15kHz
- Termination StyleConnector
- Output Voltage175V
- Output TypeSine Wave
- Inductance450 mH
- Coil Resistance1.2kOhm
- Max Frequency15kHz
- Sensing MethodInductive
- Diameter159mm
- Length104mm
- RoHS StatusNon-RoHS Compliant
- Lead FreeExempt
MA233SAN Overview
Magnetic position sensors are packaged in Barrel, Stainless Steel packages. You can set -55°C as the minimum operating temperature for magnetic position sensors. The operating temperature of this sensor module should not exceed 150°C. Sensor modules have 2 pins.
MA233SAN Features
Package / Case: Barrel, Stainless Steel
MA230 Series
Operating Temperature: -55°C~150°C TA
Frequency: 15kHz
2 Pins
MA233SAN Applications
There are a lot of Honeywell Sensing and Productivity Solutions
MA233SAN Magnetic Position Sensors Modules applications.
Gear shift selectors and driver controls (PRNDL)
Open/close sensor for LCD screens/doors/lids/trunks
Clutch/brake position sensor
Lighting actuation slave sensor
Wiper home/end position sensor
End of travel and index sensors
Industrial controls
White goods
Position and limit sensing
RPM measurement
Magnetic position sensors are packaged in Barrel, Stainless Steel packages. You can set -55°C as the minimum operating temperature for magnetic position sensors. The operating temperature of this sensor module should not exceed 150°C. Sensor modules have 2 pins.
MA233SAN Features
Package / Case: Barrel, Stainless Steel
MA230 Series
Operating Temperature: -55°C~150°C TA
Frequency: 15kHz
2 Pins
MA233SAN Applications
There are a lot of Honeywell Sensing and Productivity Solutions
MA233SAN Magnetic Position Sensors Modules applications.
Gear shift selectors and driver controls (PRNDL)
Open/close sensor for LCD screens/doors/lids/trunks
Clutch/brake position sensor
Lighting actuation slave sensor
Wiper home/end position sensor
End of travel and index sensors
Industrial controls
White goods
Position and limit sensing
RPM measurement
MA233SAN More Descriptions
Sensors, Magnetic Position Sensors, Speed and Direction - Variable Reluctance Speed Sensors
SENSOR, SEALED FRONT END, STAINLESS STEEL HOUSING, 2 PIN CONN, 3.0 IN. THREAD LE
Speed Sensor, Vrs, 0.25M/S, 175V; Supply Voltage Min:-; Supply Voltage Max:-; Sensor Terminals:Connector; Operating Temperature Min:-55°C; Operating Temperature Max:150°C; Speed Sensor Type:Vrs General Purpose; Inductance:450Mh Rohs Compliant: Yes |Honeywell MA233SAN
High Output VRS sensors are designed for use in applications where higher output voltages are needed. They perform best at low to medium speeds with medium to high impedance loads. Front-End Sealed versions are available for use where the sensor is exposed to fluids, lubricants or adverse environmental conditions. Passive VRS (Variable Reluctance Speed) Magnetic Speed sensors are simple, rugged devices that do not require an external voltage source for operation. A permanent magnet in the sensor establishes a fixed magnetic field. The approach and passing of a ferrous metal target near the sensor’s pole piece (sensing area) changes the flux lines of the magnetic field, dynamically changing its strength. This change in magnetic field strength induces a current into a coil winding which is attached to the output terminals. The output signal of a VRS sensor is an ac voltage that varies in amplitude and wave frequency as the speed of the monitored device changes, and is usually expressed in peak to peak voltage (Vp-p). One complete waveform (cycle) occurs as each target passes the sensor’s pole piece. If a standard gear were used as a target, this output signal would resemble a sine wave if viewed on an oscilloscope. Honeywell also offers VRS sensors for general purpose, power output, high resolution, high temperature, and hazardous location applications, as well as low-cost molded versions.
SENSOR, SEALED FRONT END, STAINLESS STEEL HOUSING, 2 PIN CONN, 3.0 IN. THREAD LE
Speed Sensor, Vrs, 0.25M/S, 175V; Supply Voltage Min:-; Supply Voltage Max:-; Sensor Terminals:Connector; Operating Temperature Min:-55°C; Operating Temperature Max:150°C; Speed Sensor Type:Vrs General Purpose; Inductance:450Mh Rohs Compliant: Yes |Honeywell MA233SAN
High Output VRS sensors are designed for use in applications where higher output voltages are needed. They perform best at low to medium speeds with medium to high impedance loads. Front-End Sealed versions are available for use where the sensor is exposed to fluids, lubricants or adverse environmental conditions. Passive VRS (Variable Reluctance Speed) Magnetic Speed sensors are simple, rugged devices that do not require an external voltage source for operation. A permanent magnet in the sensor establishes a fixed magnetic field. The approach and passing of a ferrous metal target near the sensor’s pole piece (sensing area) changes the flux lines of the magnetic field, dynamically changing its strength. This change in magnetic field strength induces a current into a coil winding which is attached to the output terminals. The output signal of a VRS sensor is an ac voltage that varies in amplitude and wave frequency as the speed of the monitored device changes, and is usually expressed in peak to peak voltage (Vp-p). One complete waveform (cycle) occurs as each target passes the sensor’s pole piece. If a standard gear were used as a target, this output signal would resemble a sine wave if viewed on an oscilloscope. Honeywell also offers VRS sensors for general purpose, power output, high resolution, high temperature, and hazardous location applications, as well as low-cost molded versions.
Popular Search Part Number
Related Keywords
Search Tags
Latest News
-
22 April 2024
DRV8870DDAR H-Bridge Motor Driver: Alternatives, Functional Modes, Features and More
Ⅰ. Overview of DRV8870DDARⅡ. Device functional modesⅢ. Technical parameters of DRV8870DDARⅣ. What are the power consumption characteristics of DRV8870DDAR?Ⅴ. DRV8870DDAR circuit diagramⅥ. Power supply recommendations of DRV8870DDARⅦ. Functional... -
22 April 2024
74LS161 4-BIt Synchronous Counter Functions and Applications
Ⅰ. Introduction to 74LS161Ⅱ. Pin arrangement of 74LS161Ⅲ. Working principle of 74LS161Ⅳ. 74LS161 function tableⅤ. Basic applications of 74LS161Ⅵ. How to choose the appropriate 74LS161 counter?Ⅶ. The difference... -
23 April 2024
LNK304PN Manufacturer, Highlights, Functions and Other Details
Ⅰ. LNK304PN overviewⅡ. Manufacturer of LNK304PNⅢ. Highlights of LNK304PNⅣ. Pin functional description of LNK304PNⅤ. Functions of LNK304PNⅥ. How to judge the quality of LNK304PNⅦ. How to implement the... -
23 April 2024
LM331 Frequency to Voltage Converter Functions, Working Principle and Application Circuit
Ⅰ. LM331 descriptionⅡ. Functions and roles of LM331Ⅲ. LM331 internal block diagramⅣ. Working principle of LM331Ⅴ. Application circuit of LM331Ⅵ. Specific applications of LM331Ⅶ. Precautions for using LM331The...
Help you to save your cost and time.
Reliable package for your goods.
Fast Reliable Delivery to save time.
Quality premium after-sale service.