ADI AD8626ARM-REEL

Part Number:: AD8626ARM-REEL

Manufacturer:: ADI

Ventron No:: 5149499-AD8626ARM-REEL

Description:: Precision Low Power Single-Supply JFET Amplifier

ECAD Model:

Datasheet:: AD8626ARM-REEL

Specifications

ADI AD8626ARM-REEL technical specifications, attributes, parameters and parts with similar specifications to ADI AD8626ARM-REEL.

Mounting Type
Surface Mount
Package / Case
8-TSSOP, 8-MSOP (0.118, 3.00mm Width)
Surface Mount
YES
Operating Temperature
-40°C~85°C
Packaging
Tape & Reel (TR)
JESD-609 Code
e0
Pbfree Code
no
Part Status
Obsolete
Moisture Sensitivity Level (MSL)
1 (Unlimited)
Number of Terminations
8
Terminal Finish
TIN LEAD
Subcategory
Operational Amplifier
Terminal Position
DUAL
Terminal Form
GULL WING
Peak Reflow Temperature (Cel)
240
Number of Functions
2
Supply Voltage
13V
Terminal Pitch
0.65mm
Time@Peak Reflow Temperature-Max (s)
30
Pin Count
8
JESD-30 Code
S-PDSO-G8
Output Type
Rail-to-Rail
Number of Circuits
2
Current - Supply
710μA
Slew Rate
5V/μs
Amplifier Type
J-FET
Common Mode Rejection Ratio
105 dB
Current - Input Bias
0.25pA
Voltage - Supply, Single/Dual (±)
5V~26V ±2.5V~13V
Gain Bandwidth Product
5MHz
Neg Supply Voltage-Nom (Vsup)
-13V
Unity Gain BW-Nom
5000 kHz
Average Bias Current-Max (IIB)
0.00006μA
Supply Voltage Limit-Max
13.5V
Voltage - Input Offset
350μV
Current - Output / Channel
15mA
Neg Supply Voltage-Max (Vsup)
-13.5V
Length
3mm
Height Seated (Max)
1.1mm
RoHS Status
Non-RoHS Compliant

Description

AD8626ARM-REEL Overview
In the package, you will find a 8-TSSOP, 8-MSOP (0.118, 3.00mm Width)-case to contain the op amp ic. The instrumentation amplifier in this picture is of the J-FET-type. A Tape & Reel (TR) case is used for delivering the op amp. During the past two weeks, there have been close to 8 terminations. A total of 8 pins are located on this board. This linear amplifier should be powered by an 13V battery. This particular linear amplifier is a type of Operational Amplifier device, to be precise. For this electrical component, Surface Mount is the recommended mounting type. According to the manufacturer, this buffer op amp works well at -40°C~85°C , which is a good operating temperature. A instrumentation amplifier like this has 2 circuits. Buffer amplifier produces Rail-to-Rail signals, which is one of its many benefits. There is a recommendation that this electrical part be used with a supply with 710μA current rating.

AD8626ARM-REEL Features
8 Pins
supply voltage of 13V
Output Type: Rail-to-Rail

AD8626ARM-REEL Applications
There are a lot of Rochester Electronics, LLC
AD8626ARM-REEL Instrumentational OP Amps applications.

Multiplication circuits
Division circuits
Precision measurement
Power control
Information processing
Weak signal detection
Signal amplification
Signal filtering
Signal operation
Video computer boards

AD8626ARM-REEL More Descriptions

IC OPAMP JFET 5MHZ DUAL LP 8MSOP
Operational Amplifier, 2 Func, 1350uV Offset-Max, PDSO8
The AD862x is a precision JFET input amplifier. It features true single-supply operation, low power consumption, and rail-to-rail output. The outputs remain stable with capacitive loads of over 500 pF; the supply current is less than 630 uA/amp. Applications for the AD862x include photo diode trans impedance amplification, ATE reference level drivers, battery management, both line powered and portable instrumentation, and remote sensor signal conditioning, which includes automotive sensors. The AD862xR^s ability to swing nearly rail-to-rail at the input and rail-to-rail at the output enables it to be used to buffer CMOS DA Cs, A Sics, and other wide output swing devices in single-supply systems. The 5 MHz bandwidth and low offset are ideal for precision filters. The AD862x is fully specified over the industrial temperature range. (-40oC to 85oC). The AD8627 is available in both 5-lead SC70 and 8-lead SOIC surface-mount packages (SC70 packaged parts are available in tape and reel only). The AD8626 is available in MSOP and SOIC packages, while the AD8625 is available in TS SOP and SOIC packages.

Certification