Analog Devices Inc. AD602JR-REEL7
- Part Number:
- AD602JR-REEL7
- Manufacturer:
- Analog Devices Inc.
- Ventron No:
- 3192120-AD602JR-REEL7
- Description:
- IC OPAMP VGA 35MHZ 16SOIC
- Datasheet:
- AD602JR-REEL7
Analog Devices Inc. AD602JR-REEL7 technical specifications, attributes, parameters and parts with similar specifications to Analog Devices Inc. AD602JR-REEL7.
- Mounting TypeSurface Mount
- Package / Case16-SOIC (0.295, 7.50mm Width)
- Surface MountYES
- Operating Temperature0°C~70°C
- PackagingTape & Reel (TR)
- SeriesX-AMP®
- JESD-609 Codee0
- Pbfree Codeno
- Part StatusObsolete
- Moisture Sensitivity Level (MSL)1 (Unlimited)
- Number of Terminations16
- Terminal FinishTIN LEAD
- Terminal PositionDUAL
- Terminal FormGULL WING
- Peak Reflow Temperature (Cel)240
- Number of Functions1
- Supply Voltage5V
- Reach Compliance Codeunknown
- Time@Peak Reflow Temperature-Max (s)30
- Pin Count16
- JESD-30 CodeR-PDSO-G16
- Supply Voltage-Min (Vsup)4.75V
- Number of Circuits2
- Analog IC - Other TypeANALOG CIRCUIT
- Current - Supply11mA
- Slew Rate275V/μs
- Amplifier TypeVariable Gain
- Current - Input Bias350nA
- Voltage - Supply, Single/Dual (±)±4.75V~5.25V
- Neg Supply Voltage-Nom (Vsup)-5V
- Current - Output / Channel50mA
- 3db Bandwidth35MHz
- Length10.3mm
- RoHS StatusNon-RoHS Compliant
AD602JR-REEL7 Overview
The linear amplifier is packaged in a 16-SOIC (0.295, 7.50mm Width) case. This is a Variable Gain type op amp. Linear amplifier is delivered in a Tape & Reel (TR) case. The number of terminations approaches 16. Buffer amplifier has a total of 16 pins. Please take in mind that this instrumentation amplifier should be run at 5V. Surface Mount is the recommended mounting type for this linear amplifier. With regard to operating temperature, this op amp functions well at 0°C~70°C. There are 2 circuits on this op amp. It is recommended that this electronic component be used with an 11mA supply. X-AMP® corresponds to the op amp's series. The other type of analog IC used in this op amp ic is known as ANALOG CIRCUIT.
AD602JR-REEL7 Features
16 Pins
supply voltage of 5V
AD602JR-REEL7 Applications
There are a lot of Rochester Electronics, LLC
AD602JR-REEL7 Instrumentational OP Amps applications.
Inverse/same-phase proportional circuit
Addition operation circuits
Subtraction operation circuits
single/dual op amp sum and difference circuits
Integrator circuits
Differentiator circuits
Logarithmic operation circuits
Exponential operation circuits
Multiplication circuits
Division circuits
The linear amplifier is packaged in a 16-SOIC (0.295, 7.50mm Width) case. This is a Variable Gain type op amp. Linear amplifier is delivered in a Tape & Reel (TR) case. The number of terminations approaches 16. Buffer amplifier has a total of 16 pins. Please take in mind that this instrumentation amplifier should be run at 5V. Surface Mount is the recommended mounting type for this linear amplifier. With regard to operating temperature, this op amp functions well at 0°C~70°C. There are 2 circuits on this op amp. It is recommended that this electronic component be used with an 11mA supply. X-AMP® corresponds to the op amp's series. The other type of analog IC used in this op amp ic is known as ANALOG CIRCUIT.
AD602JR-REEL7 Features
16 Pins
supply voltage of 5V
AD602JR-REEL7 Applications
There are a lot of Rochester Electronics, LLC
AD602JR-REEL7 Instrumentational OP Amps applications.
Inverse/same-phase proportional circuit
Addition operation circuits
Subtraction operation circuits
single/dual op amp sum and difference circuits
Integrator circuits
Differentiator circuits
Logarithmic operation circuits
Exponential operation circuits
Multiplication circuits
Division circuits
AD602JR-REEL7 More Descriptions
IC,Voltage Controlled Gain Amplifier,DUAL,CMOS,SOP,16PIN,PLASTIC
IC VARIABLE GAIN 2 CIRC 16SOIC
French Electronic Distributor since 1988
The AD600/AD602 dual channel, low noise, variable gain amplifiers are optimized for use in ultrasound imaging systems, but are applicable to any application requiring precise gain, low noise and distortion, and wide bandwidth. Each independent channel provides a gain of 0 dB to 40 dB in the AD600 and -10 dB to 30 dB in the AD602. The lower gain of the AD602 results in an improved signal-to-noise ratio (SNR) at the output. However, both products have the same 1.4 nV/vHz input noise spectral density. The decibel gain is directly proportional to the control voltage, accurately calibrated, and supply and temperature-stable. To achieve the difficult performance objectives, a proprietary circuit form, the X-AMP®, was developed. Each channel of the X-AMP comprises a variable attenuator of 0 dB to -42.14 dB followed by a high speed fixed gain amplifier. In this way, the amplifier never has to cope with large inputs, and can benefit from the use of negative feedback to precisely define the gain and dynamics. The attenuator is realized as a 7-stage R-2R ladder network having an input resistance of 100 W, laser trimmed to ±2%. The attenuation between tap points is 6.02 dB; the gain-control circuit provides continuous interpolation between these taps. The resulting control function is linear in dB. The gain-control interfaces are fully differential, providing an input resistance of ~15 M W and a scale factor of 32 dB/V (that is, 31.25 mV/dB) defined by an internal voltage reference. The response time of this interface is less than 1 µs. Each channel also has an independent gating facility that optionally blocks signal transmission and sets the dc output level to within a few millivolts of the output ground. The gating control input is TTL- and CMOS-compatible. The maximum gain of the AD600 is 41.07 dB, and the maximum gain of the AD602 is 31.07 dB; the -3 dB bandwidth of both models is nominally 35 MHz, essentially independent of the gain. The SNR for a 1 V rms output and a 1 MHz noise bandwidth is typically 76 dB for the AD600 and 86 dB for the AD602. The amplitude response is flat within ±0.5 dB from 100 kHz to 10 MHz; over this frequency range, the group delay varies by less than ±2 ns at all gain settings. Each amplifier channel can drive 100 W load impedances with low distortion. For example, the peak specified output is ±2.5 V minimum into a 500 W load, or ±1 V into a 100 W load. For a 200 W load in shunt with 5 pF, the total harmonic distortion for a ±1 V sinusoidal output at 10 MHz is typically -60 dBc. The AD600J/AD602J are specified for operation from 0°C to 70°C and are available in 16-lead PDIP (N) and 16-lead SOIC packages. The AD600A/AD602A are specified for operation from -40°C to 85°C and are available in 16-lead CERDIP (Q) and 16-lead SOIC packages. The AD600S/AD602S are specified for operation from -55°C to 125°C, are available in a 16-lead CERDIP (Q) package, and are MIL-STD-883 compliant. The AD600S/AD602S are also available under DESC SMD 5962-94572. AD600 - Gain Range: 0 dB to 40 dB AD602 - Gain Range: -10 dB to 30 dB
IC VARIABLE GAIN 2 CIRC 16SOIC
French Electronic Distributor since 1988
The AD600/AD602 dual channel, low noise, variable gain amplifiers are optimized for use in ultrasound imaging systems, but are applicable to any application requiring precise gain, low noise and distortion, and wide bandwidth. Each independent channel provides a gain of 0 dB to 40 dB in the AD600 and -10 dB to 30 dB in the AD602. The lower gain of the AD602 results in an improved signal-to-noise ratio (SNR) at the output. However, both products have the same 1.4 nV/vHz input noise spectral density. The decibel gain is directly proportional to the control voltage, accurately calibrated, and supply and temperature-stable. To achieve the difficult performance objectives, a proprietary circuit form, the X-AMP®, was developed. Each channel of the X-AMP comprises a variable attenuator of 0 dB to -42.14 dB followed by a high speed fixed gain amplifier. In this way, the amplifier never has to cope with large inputs, and can benefit from the use of negative feedback to precisely define the gain and dynamics. The attenuator is realized as a 7-stage R-2R ladder network having an input resistance of 100 W, laser trimmed to ±2%. The attenuation between tap points is 6.02 dB; the gain-control circuit provides continuous interpolation between these taps. The resulting control function is linear in dB. The gain-control interfaces are fully differential, providing an input resistance of ~15 M W and a scale factor of 32 dB/V (that is, 31.25 mV/dB) defined by an internal voltage reference. The response time of this interface is less than 1 µs. Each channel also has an independent gating facility that optionally blocks signal transmission and sets the dc output level to within a few millivolts of the output ground. The gating control input is TTL- and CMOS-compatible. The maximum gain of the AD600 is 41.07 dB, and the maximum gain of the AD602 is 31.07 dB; the -3 dB bandwidth of both models is nominally 35 MHz, essentially independent of the gain. The SNR for a 1 V rms output and a 1 MHz noise bandwidth is typically 76 dB for the AD600 and 86 dB for the AD602. The amplitude response is flat within ±0.5 dB from 100 kHz to 10 MHz; over this frequency range, the group delay varies by less than ±2 ns at all gain settings. Each amplifier channel can drive 100 W load impedances with low distortion. For example, the peak specified output is ±2.5 V minimum into a 500 W load, or ±1 V into a 100 W load. For a 200 W load in shunt with 5 pF, the total harmonic distortion for a ±1 V sinusoidal output at 10 MHz is typically -60 dBc. The AD600J/AD602J are specified for operation from 0°C to 70°C and are available in 16-lead PDIP (N) and 16-lead SOIC packages. The AD600A/AD602A are specified for operation from -40°C to 85°C and are available in 16-lead CERDIP (Q) and 16-lead SOIC packages. The AD600S/AD602S are specified for operation from -55°C to 125°C, are available in a 16-lead CERDIP (Q) package, and are MIL-STD-883 compliant. The AD600S/AD602S are also available under DESC SMD 5962-94572. AD600 - Gain Range: 0 dB to 40 dB AD602 - Gain Range: -10 dB to 30 dB
Popular Search Part Number
Related Keywords
Search Tags
Latest News
-
29 March 2024
TLP2362 Optocoupler Characteristics, Specifications, Working Principle and More
Ⅰ. Overview of TLP2362Ⅱ. Characteristics of TLP2362Ⅲ. Specifications of TLP2362Ⅳ. Recommended operating conditions of TLP2362Ⅴ. How does TLP2362 work?Ⅵ. Internal equivalent circuit of TLP2362Ⅶ. Storage and soldering of... -
29 March 2024
STM32H743VIT6 Specifications, Characteristics, Pinout and Market Situation
Ⅰ. Description of STM32H743VIT6Ⅱ. Specifications of STM32H743VIT6Ⅲ. Characteristics of STM32H743VIT6Ⅳ. How to use STM32H743VIT6?Ⅴ. STM32H743VIT6 pinoutⅥ. Low-power strategy of STM32H743VIT6Ⅶ. Market situation of STM32H743VIT6Ⅰ. Description of STM32H743VIT6The STM32H743VIT6... -
01 April 2024
XCF32PFSG48C Symbol, Manufacturer, Specifications and Programming
Ⅰ. Overview of XCF32PFSG48CⅡ. Symbol, footprint and 3D model of XCF32PFSG48CⅢ. Manufacturer of XCF32PFSG48CⅣ. Reset and power-on reset activationⅤ. Specifications of XCF32PFSG48CⅥ. Programming of XCF32PFSG48CⅦ. In which emerging... -
01 April 2024
M24C16-RMN6TP Structure, Advantages, Package and Other Details
Ⅰ. M24C16-RMN6TP descriptionⅡ. Basic structure and working principle of M24C16-RMN6TPⅢ. Technical parameters of M24C16-RMN6TPⅣ. What are the market competitive advantages of M24C16-RMN6TP?Ⅴ. Package of M24C16-RMN6TPⅥ. Data transmission process...
Help you to save your cost and time.
Reliable package for your goods.
Fast Reliable Delivery to save time.
Quality premium after-sale service.