Diodes Incorporated TL072SG-13
- Part Number:
- TL072SG-13
- Manufacturer:
- Diodes Incorporated
- Ventron No:
- 3690104-TL072SG-13
- Description:
- IC OPAMP JFET 3MHZ 8SOP
- Datasheet:
- TL072SG-13
Diodes Incorporated TL072SG-13 technical specifications, attributes, parameters and parts with similar specifications to Diodes Incorporated TL072SG-13.
- Factory Lead Time13 Weeks
- Contact PlatingTin
- MountSurface Mount
- Mounting TypeSurface Mount
- Package / Case8-SOIC (0.154, 3.90mm Width)
- Number of Pins8
- Supplier Device Package8-SOP
- Weight73.992255mg
- Operating Temperature-40°C~85°C
- PackagingCut Tape (CT)
- Published2009
- Part StatusActive
- Moisture Sensitivity Level (MSL)1 (Unlimited)
- Max Operating Temperature85°C
- Min Operating Temperature-40°C
- Max Power Dissipation860mW
- Base Part NumberTL072
- Operating Supply Voltage15V
- Number of Elements2
- Number of Channels2
- Number of Circuits2
- Operating Supply Current1.4mA
- Power Dissipation860mW
- Current - Supply1.4mA
- Slew Rate13V/μs
- Amplifier TypeJ-FET
- Common Mode Rejection Ratio75 dB
- Current - Input Bias65pA
- Voltage - Supply, Single/Dual (±)10V~30V ±5V~15V
- Supply TypeDual
- Input Offset Voltage (Vos)6mV
- Bandwidth3MHz
- Gain Bandwidth Product3MHz
- Voltage Gain106.02dB
- Voltage - Input Offset3mV
- Dual Supply Voltage15V
- Number of Amplifiers2
- Height1.5mm
- Length4.95mm
- Width3.95mm
- REACH SVHCNo SVHC
- Radiation HardeningNo
- RoHS StatusROHS3 Compliant
- Lead FreeLead Free
TL072SG-13 Overview
In order to protect the op amps, a 8-SOIC (0.154, 3.90mm Width) case is used. There are two types of operational amplifiers in this circuit. In the case of Cut Tape (CT) cases, linear amplifier will be delivered. It has 8 pins that make up the linear amplifier. In terms of input offset voltage, operational amplifier rates 6mV. This electronic component is recommended to be mounted using the mounting type Surface Mount. It is recommended that this op amp ic be operated at a temperature no higher than -40°C~85°C for optimal performance. In order for this instrumentation amplifier to operate, the supply current needs to be between 1.4mA and 10 . Maintain 106.02dB as the voltage gain. In total, there are 2 circuits on this buffer amplifier. Buffer op amp is equipped with 2 channels on the device. It is recommended that the temperature of this op amp ic should not fall below -40°C degrees Fahrenheit at any time. Linear amplifier shouldn't be used above 85°C degrees. As a whole, there are 2 elements that make up this buffer amplifier. The operating supply voltage of the buffer op amp is rated at 15V. This electronic part is recommended to be used with an 1.4mA supply for best performance. A linear amplifier such as this has 2 amplifiers on it.
TL072SG-13 Features
106.02dB voltage gain
TL072SG-13 Applications
There are a lot of Diodes Incorporated
TL072SG-13 Instrumentational OP Amps applications.
Differentiator circuits
Logarithmic operation circuits
Exponential operation circuits
Multiplication circuits
Division circuits
Precision measurement
Power control
Information processing
Weak signal detection
Signal amplification
In order to protect the op amps, a 8-SOIC (0.154, 3.90mm Width) case is used. There are two types of operational amplifiers in this circuit. In the case of Cut Tape (CT) cases, linear amplifier will be delivered. It has 8 pins that make up the linear amplifier. In terms of input offset voltage, operational amplifier rates 6mV. This electronic component is recommended to be mounted using the mounting type Surface Mount. It is recommended that this op amp ic be operated at a temperature no higher than -40°C~85°C for optimal performance. In order for this instrumentation amplifier to operate, the supply current needs to be between 1.4mA and 10 . Maintain 106.02dB as the voltage gain. In total, there are 2 circuits on this buffer amplifier. Buffer op amp is equipped with 2 channels on the device. It is recommended that the temperature of this op amp ic should not fall below -40°C degrees Fahrenheit at any time. Linear amplifier shouldn't be used above 85°C degrees. As a whole, there are 2 elements that make up this buffer amplifier. The operating supply voltage of the buffer op amp is rated at 15V. This electronic part is recommended to be used with an 1.4mA supply for best performance. A linear amplifier such as this has 2 amplifiers on it.
TL072SG-13 Features
106.02dB voltage gain
TL072SG-13 Applications
There are a lot of Diodes Incorporated
TL072SG-13 Instrumentational OP Amps applications.
Differentiator circuits
Logarithmic operation circuits
Exponential operation circuits
Multiplication circuits
Division circuits
Precision measurement
Power control
Information processing
Weak signal detection
Signal amplification
TL072SG-13 More Descriptions
IC OPAMP JFET 3MHZ 8SOP / Op Amp Dual Low Noise Amplifier 8-Pin SOP EP T/R
Operational Amplifier, 2 Func, 8000uV Offset-Max, BIPolar, PDSO8
Operational Amplifier, Dual, 3 Mhz, 2, 13 V/ S, Soic, 8 Rohs Compliant: Yes |Diodes Inc. TL072SG-13
OP AMP, JFET, DUAL, 8-SOIC; No. of Amplifiers: 2 Amplifier; Bandwidth: 3MHz; Slew Rate: 13V/µs; Supply Voltage Range: -; Amplifier Case Style: SOIC; No. of Pins: 8Pin; Available until stocks are exhausted Alternative available
Operational Amplifier, 2 Func, 8000uV Offset-Max, BIPolar, PDSO8
Operational Amplifier, Dual, 3 Mhz, 2, 13 V/ S, Soic, 8 Rohs Compliant: Yes |Diodes Inc. TL072SG-13
OP AMP, JFET, DUAL, 8-SOIC; No. of Amplifiers: 2 Amplifier; Bandwidth: 3MHz; Slew Rate: 13V/µs; Supply Voltage Range: -; Amplifier Case Style: SOIC; No. of Pins: 8Pin; Available until stocks are exhausted Alternative available
Popular Search Part Number
Related Keywords
Search Tags
Latest News
-
02 November 2023
MPX2010DP Pressure Sensor: Manufacturer, Pin Configuration, and Applications
Ⅰ. What is a pressure sensor?Ⅱ. Overview of MPX2010DP pressure sensorⅢ. Manufacturer of MPX2010DP pressure sensorⅣ. MPX2010DP symbol, footprint and pin configurationⅤ. Features of MPX2010DP pressure sensorⅥ. Technical... -
02 November 2023
S8050 Bipolar Transistor: Manufacturer, Specifications, S8050 vs SS8050 and More Details
Ⅰ. Introduction to S8050 transistorⅡ. Manufacturer of S8050 transistorⅢ. Specifications of S8050 transistorⅣ. Symbol, footprint and pin configuration of S8050 transistorⅤ. What are the features of S8050 transistor?Ⅵ.... -
03 November 2023
ULN2003AD Equivalents, Symbol, Working Principle and Layout Guidelines
Ⅰ. Overview of ULN2003ADⅡ. Symbol, footprint and pin configuration of ULN2003ADⅢ. Features of ULN2003ADⅣ. Technical parameters of ULN2003ADⅤ. Working principle of ULN2003ADⅥ. Layout guidelines for ULN2003ADⅦ. What are... -
03 November 2023
TCA9548APWR Symbol, Features, Layout Guidelines and TCA9548APWR vs PCA9548APW-T
Ⅰ. What is a multiplexer?Ⅱ. Overview of TCA9548APWRⅢ. TCA9548APWR symbol, footprint and pin configurationⅣ. What are the features of TCA9548APWR?Ⅴ. Technical parameters of TCA9548APWRⅥ. Layout guidelines for TCA9548APWRⅦ....
Help you to save your cost and time.
Reliable package for your goods.
Fast Reliable Delivery to save time.
Quality premium after-sale service.