Fairchild/ON Semiconductor MM74HCT374WMX
- Part Number:
- MM74HCT374WMX
- Manufacturer:
- Fairchild/ON Semiconductor
- Ventron No:
- 3706670-MM74HCT374WMX
- Description:
- IC D-TYPE POS TRG SNGL 20SOIC
- ECAD Model:
-
- Datasheet:
- MM74HCT374WMX
Fairchild/ON Semiconductor MM74HCT374WMX technical specifications, attributes, parameters and parts with similar specifications to Fairchild/ON Semiconductor MM74HCT374WMX.
- Factory Lead Time4 Weeks
- Lifecycle StatusACTIVE (Last Updated: 2 days ago)
- MountSurface Mount
- Mounting TypeSurface Mount
- Package / Case20-SOIC (0.295, 7.50mm Width)
- Number of Pins20
- Weight801mg
- Operating Temperature-40°C~85°C TA
- PackagingTape & Reel (TR)
- Published2005
- Series74HCT
- JESD-609 Codee3
- Pbfree Codeyes
- Part StatusActive
- Moisture Sensitivity Level (MSL)1 (Unlimited)
- Number of Terminations20
- ECCN CodeEAR99
- Terminal FinishTin (Sn)
- SubcategoryFF/Latches
- Packing MethodTAPE AND REEL
- TechnologyCMOS
- Voltage - Supply4.5V~5.5V
- Terminal PositionDUAL
- Terminal FormGULL WING
- Supply Voltage5V
- Base Part Number74HCT374
- FunctionStandard
- Output TypeTri-State, Non-Inverted
- Operating Supply Voltage5V
- Number of Elements1
- PolarityNon-Inverting
- Power Supplies5V
- Number of Circuits8
- Load Capacitance50pF
- Number of Ports2
- Number of Bits8
- Clock Frequency30MHz
- Propagation Delay57 ns
- Turn On Delay Time30 ns
- FamilyHCT
- Logic FunctionD-Type, Flip-Flop
- Current - Quiescent (Iq)8μA
- Current - Output High, Low7.2mA 7.2mA
- Max I(ol)0.006 A
- Max Propagation Delay @ V, Max CL46ns @ 5V, 150pF
- Trigger TypePositive Edge
- Input Capacitance10pF
- Number of Output Lines3
- Clock Edge Trigger TypePositive Edge
- Width7.5mm
- Radiation HardeningNo
- RoHS StatusROHS3 Compliant
- Lead FreeLead Free
MM74HCT374WMX Overview
20-SOIC (0.295, 7.50mm Width)is the way it is packaged. It is included in the package Tape & Reel (TR). Tri-State, Non-Invertedis the output configured for it. JK flip flop uses Positive Edgeas the trigger. Surface Mountmounts this electrical part. A supply voltage of 4.5V~5.5V is required for operation. Currently, the operating temperature is -40°C~85°C TA. There is D-Type type of electronic flip flop associated with this device. It is a type of FPGA belonging to the 74HCT series. There should be no greater frequency than 30MHzon its output. There are 1 elements in it. Despite external influences, it consumes 8μAof quiescent current. A total of 20terminations have been recorded. You can search similar parts based on 74HCT374. A voltage of 5V is used to power it. JK flip flop input capacitance is 10pF farads. It is a member of the HCTfamily of D flip flop. It is mounted in the way of Surface Mount. 20pins are included in its design. It has a clock edge trigger type of Positive Edge. There is a base part number FF/Latchesfor the RS flip flops. The flip flop is designed with 8bits. Due to its superior flexibility, it uses 8 circuits. Compared to other similar T flip flops, this device offers reliable performance and is well suited for TAPE AND REEL. There are 5V power supplies attached to it. The flip flop contains 2ports. High efficiency requires the supply voltage to be maintained at 5V. There are 3 output lines on it.
MM74HCT374WMX Features
Tape & Reel (TR) package
74HCT series
20 pins
8 Bits
5V power supplies
MM74HCT374WMX Applications
There are a lot of ON Semiconductor MM74HCT374WMX Flip Flops applications.
QML qualified product
Data storage
Pattern generators
Data transfer
Bus hold
Storage Registers
Convert a momentary switch to a toggle switch
ATE
Buffer registers
Patented noise
20-SOIC (0.295, 7.50mm Width)is the way it is packaged. It is included in the package Tape & Reel (TR). Tri-State, Non-Invertedis the output configured for it. JK flip flop uses Positive Edgeas the trigger. Surface Mountmounts this electrical part. A supply voltage of 4.5V~5.5V is required for operation. Currently, the operating temperature is -40°C~85°C TA. There is D-Type type of electronic flip flop associated with this device. It is a type of FPGA belonging to the 74HCT series. There should be no greater frequency than 30MHzon its output. There are 1 elements in it. Despite external influences, it consumes 8μAof quiescent current. A total of 20terminations have been recorded. You can search similar parts based on 74HCT374. A voltage of 5V is used to power it. JK flip flop input capacitance is 10pF farads. It is a member of the HCTfamily of D flip flop. It is mounted in the way of Surface Mount. 20pins are included in its design. It has a clock edge trigger type of Positive Edge. There is a base part number FF/Latchesfor the RS flip flops. The flip flop is designed with 8bits. Due to its superior flexibility, it uses 8 circuits. Compared to other similar T flip flops, this device offers reliable performance and is well suited for TAPE AND REEL. There are 5V power supplies attached to it. The flip flop contains 2ports. High efficiency requires the supply voltage to be maintained at 5V. There are 3 output lines on it.
MM74HCT374WMX Features
Tape & Reel (TR) package
74HCT series
20 pins
8 Bits
5V power supplies
MM74HCT374WMX Applications
There are a lot of ON Semiconductor MM74HCT374WMX Flip Flops applications.
QML qualified product
Data storage
Pattern generators
Data transfer
Bus hold
Storage Registers
Convert a momentary switch to a toggle switch
ATE
Buffer registers
Patented noise
MM74HCT374WMX More Descriptions
Flip Flop D-Type Bus Interface Pos-Edge 3-ST 1-Element 20-Pin SOIC W T/R
Ic,flip-Flop,octal,d Type,hct-Cmos,sop,20Pin,plastic Rohs Compliant: Yes |Onsemi MM74HCT374WMX
Tape & Reel (TR) 74HCT374 e3 74HCT flip flop 801mg 46ns @ 5V 150pF 30MHz 57ns
The MM74HCT373 octal D-type latches and MM74HCT374 Octal D-type flip flops advanced silicon-gate CMOS technology, which provides the inherent benefits of low power consumption and wide power supply range, but are LS-TTL input and output characteristic & pin-out compatible. The 3-STATE outputs are capable of driving 15 LS-TTL loads. All inputs are protected from damage due to static discharge by internal diodes to VCC and ground. When the MM74HCT373 LATCH ENABLE input is HIGH, the Q outputs will follow the D inputs. When the LATCH ENABLE goes LOW, data at the D inputs will be retained at the outputs until LATCH ENABLE returns HIGH again. When a high logic level is applied to the OUTPUT CONTROL input, all outputs go to a high impedance state, regardless of what signals are present at the other inputs and the state of the storage elements. The MM74HCT374 are positive edge triggered flip-flops. Data at the D inputs, meeting the setup and hold time requirements, are transferred to the Q outputs on positive going transitions of the CLOCK (CK) input. When a high logic level is applied to the OUTPUT CONTROL (OC) input, all outputs go to a high impedance state, regardless of what signals are present at the other inputs and the state of the storage elements. MM74HCT devices are intended to interface between TTL and NMOS components and standard CMOS devices. These parts are also plug in replacements for LS-TTL devices and can be used to reduce power consumption in existing designs.
Ic,flip-Flop,octal,d Type,hct-Cmos,sop,20Pin,plastic Rohs Compliant: Yes |Onsemi MM74HCT374WMX
Tape & Reel (TR) 74HCT374 e3 74HCT flip flop 801mg 46ns @ 5V 150pF 30MHz 57ns
The MM74HCT373 octal D-type latches and MM74HCT374 Octal D-type flip flops advanced silicon-gate CMOS technology, which provides the inherent benefits of low power consumption and wide power supply range, but are LS-TTL input and output characteristic & pin-out compatible. The 3-STATE outputs are capable of driving 15 LS-TTL loads. All inputs are protected from damage due to static discharge by internal diodes to VCC and ground. When the MM74HCT373 LATCH ENABLE input is HIGH, the Q outputs will follow the D inputs. When the LATCH ENABLE goes LOW, data at the D inputs will be retained at the outputs until LATCH ENABLE returns HIGH again. When a high logic level is applied to the OUTPUT CONTROL input, all outputs go to a high impedance state, regardless of what signals are present at the other inputs and the state of the storage elements. The MM74HCT374 are positive edge triggered flip-flops. Data at the D inputs, meeting the setup and hold time requirements, are transferred to the Q outputs on positive going transitions of the CLOCK (CK) input. When a high logic level is applied to the OUTPUT CONTROL (OC) input, all outputs go to a high impedance state, regardless of what signals are present at the other inputs and the state of the storage elements. MM74HCT devices are intended to interface between TTL and NMOS components and standard CMOS devices. These parts are also plug in replacements for LS-TTL devices and can be used to reduce power consumption in existing designs.
Popular Search Part Number
Related Keywords
Search Tags
Latest News
-
21 September 2023
8 bit AVR Microcontroller ATMEGA32U4-AU
Ⅰ. Overview of ATMEGA32U4-AUⅡ. Symbol and Footprint of ATMEGA32U4-AUⅢ. Technical parametersⅣ. Features of ATMEGA32U4-AUⅤ. Pin descriptionⅥ. What types of products is ATMEGA32U4-AU suitable for?Ⅰ. Overview of ATMEGA32U4-AUATMEGA32U4-AU is... -
21 September 2023
Difference Between 2N2222 and BC547 Transistor
Ⅰ. What is 2N2222?Ⅱ. What is BC547?Ⅲ. 2N2222 vs BC547 symbolⅣ. 2N2222 vs BC547 technical parametersⅤ. 2N2222 vs BC547 pin comparisonⅥ. 2N2222 vs BC547 featuresⅦ. 2N2222 vs BC547... -
22 September 2023
Power Transistor IC LM317LZ: Symbol, Features and Package
Ⅰ. Overview of LM317LZⅡ. Symbol and Footprint of LM317LZⅢ. Technical parametersⅣ. Features of LM317LZⅤ. Pins and package of LM317LZⅥ. Advantages and disadvantages of LM317LZⅦ. How to optimize the... -
22 September 2023
LM301AN Operational Amplifier: Equivalent, Circuit and Package
Ⅰ. What is LM301AN？Ⅱ. Symbol, footprint and pin connection of LM301ANⅢ. Technical parametersⅣ. LM301AN tone control circuitⅤ. Features of LM301ANⅥ. What is the difference between LM301AN and LM709?Ⅶ....
Help you to save your cost and time.
Reliable package for your goods.
Fast Reliable Delivery to save time.
Quality premium after-sale service.