Texas Instruments INA132UG4
- Part Number:
- INA132UG4
- Manufacturer:
- Texas Instruments
- Ventron No:
- 3698133-INA132UG4
- Description:
- IC OPAMP DIFF 300KHZ 8SOIC
- Datasheet:
- INA132UG4
Texas Instruments INA132UG4 technical specifications, attributes, parameters and parts with similar specifications to Texas Instruments INA132UG4.
- Package / CaseSOIC
- Surface MountYES
- Number of Pins8
- Weight75.891673mg
- JESD-609 Codee4
- Pbfree Codeno
- Moisture Sensitivity Level (MSL)3 (168 Hours)
- Number of Terminations8
- Resistance80kOhm
- Terminal FinishNickel/Palladium/Gold (Ni/Pd/Au)
- Max Operating Temperature85°C
- Min Operating Temperature-40°C
- Additional FeatureIT CAN ALSO OPERATE WITH 2.7V TO 36V SINGLE SUPPLY
- Terminal PositionDUAL
- Terminal FormGULL WING
- Peak Reflow Temperature (Cel)260
- Number of Functions1
- Supply Voltage15V
- Time@Peak Reflow Temperature-Max (s)NOT SPECIFIED
- Pin Count8
- Qualification StatusNot Qualified
- Operating Supply Voltage5V
- Number of Elements1
- Temperature GradeINDUSTRIAL
- Max Supply Voltage36V
- Min Supply Voltage2.7V
- Analog IC - Other TypeANALOG CIRCUIT
- Operating Supply Current160μA
- Nominal Supply Current160μA
- Quiescent Current160μA
- Slew Rate0.1 V/μs
- Common Mode Rejection Ratio76 dB
- Output Current per Channel12mA
- Input Offset Voltage (Vos)500μV
- Bandwidth300 kHz
- Neg Supply Voltage-Nom (Vsup)-15V
- Voltage Gain0dB
- Max Dual Supply Voltage18V
- 3db Bandwidth300 kHz
- Min Dual Supply Voltage1.35V
- Dual Supply Voltage15V
- Height1.58mm
- Length4.9mm
- Width3.91mm
- RoHS StatusRoHS Compliant
- Lead FreeContains Lead
INA132UG4 Overview
A SOIC case is used to package the op amp. It is estimated that there will be 8 terminations in the next few months. There are a total of 8 pins on this op amp. It is important to remember that this op amp should be operated at a voltage of 15V volts. There are 8 pins on this chip. In terms of the input offset voltage, instrumentation amplifier rates at 500μV. An 160μA volt supply current is needed for this linear amplifier to operate. There should be no change in the voltage gain. In order for op amp to function properly, the temperature should not be lower than -40°C degrees Celsius. Instrumentation amplifier should only be used at temperatures up to 85°C. There are a total of 1 elements in this linear amplifier. The operating supply voltage of the buffer op amp is rated at 5V. I would like to point out that this electrical component is capable of working from a voltage below 36V as far as the power supply is concerned. As a general rule, it is advisable to keep the op amp's supply voltage above 2.7V at all times. The dual supply voltage of 18V should be used for the conduct of this electronic component. There is a quiescent current of 160μA in this operational amplifier circuit. 80kOhm should be the range of resistance for the linear amplifier. There is also another type of analog IC used in this op amp ic that is called a ANALOG CIRCUIT-type IC. I would like to draw your attention to the following extra benefit of this buffer amplifier: IT CAN ALSO OPERATE WITH 2.7V TO 36V SINGLE SUPPLY.
INA132UG4 Features
8 Pins
supply voltage of 15V
0dB voltage gain
Resistance of 80kOhm
INA132UG4 Applications
There are a lot of Texas Instruments
INA132UG4 Instrumentational OP Amps applications.
Addition operation circuits
Subtraction operation circuits
single/dual op amp sum and difference circuits
Integrator circuits
Differentiator circuits
Logarithmic operation circuits
Exponential operation circuits
Multiplication circuits
Division circuits
Precision measurement
A SOIC case is used to package the op amp. It is estimated that there will be 8 terminations in the next few months. There are a total of 8 pins on this op amp. It is important to remember that this op amp should be operated at a voltage of 15V volts. There are 8 pins on this chip. In terms of the input offset voltage, instrumentation amplifier rates at 500μV. An 160μA volt supply current is needed for this linear amplifier to operate. There should be no change in the voltage gain. In order for op amp to function properly, the temperature should not be lower than -40°C degrees Celsius. Instrumentation amplifier should only be used at temperatures up to 85°C. There are a total of 1 elements in this linear amplifier. The operating supply voltage of the buffer op amp is rated at 5V. I would like to point out that this electrical component is capable of working from a voltage below 36V as far as the power supply is concerned. As a general rule, it is advisable to keep the op amp's supply voltage above 2.7V at all times. The dual supply voltage of 18V should be used for the conduct of this electronic component. There is a quiescent current of 160μA in this operational amplifier circuit. 80kOhm should be the range of resistance for the linear amplifier. There is also another type of analog IC used in this op amp ic that is called a ANALOG CIRCUIT-type IC. I would like to draw your attention to the following extra benefit of this buffer amplifier: IT CAN ALSO OPERATE WITH 2.7V TO 36V SINGLE SUPPLY.
INA132UG4 Features
8 Pins
supply voltage of 15V
0dB voltage gain
Resistance of 80kOhm
INA132UG4 Applications
There are a lot of Texas Instruments
INA132UG4 Instrumentational OP Amps applications.
Addition operation circuits
Subtraction operation circuits
single/dual op amp sum and difference circuits
Integrator circuits
Differentiator circuits
Logarithmic operation circuits
Exponential operation circuits
Multiplication circuits
Division circuits
Precision measurement
INA132UG4 More Descriptions
SP Amp Difference Amplifier Single ±18V/36V 8-Pin SOIC Tube
Low Power, Single-Supply Difference Amplifier 8-SOIC
Instrumentation Amplifier IC; Gain Max, V/V:1; Supply Voltage Min:2.7V; Supply Voltage Max:36V; Package/Case:8-SOIC; No. of Pins:8; Common Mode Ratio:76 dB; Leaded Process Compatible:Yes; Peak Reflow Compatible (260 C):Yes ;RoHS Compliant: Yes
Low Power, Single-Supply Difference Amplifier 8-SOIC
Instrumentation Amplifier IC; Gain Max, V/V:1; Supply Voltage Min:2.7V; Supply Voltage Max:36V; Package/Case:8-SOIC; No. of Pins:8; Common Mode Ratio:76 dB; Leaded Process Compatible:Yes; Peak Reflow Compatible (260 C):Yes ;RoHS Compliant: Yes
Popular Search Part Number
Related Keywords
Search Tags
Latest News
-
27 September 2023
BC640 PNP Transistor: Features, Package and Other Details
Ⅰ. Overview of BC640Ⅱ. Symbol and footprint of BC640Ⅲ. Technical parametersⅣ. Features of BC640Ⅴ. Pinout and package of BC640Ⅵ. Application of BC640Ⅶ. How to optimize the performance of... -
27 September 2023
Introduction to the BTS7960B Motor Drive Module
Ⅰ. What is BTS7960B?Ⅱ. BTS7960B symbol, footprint and pin configurationⅢ. Technical parametersⅣ. Features of BTS7960BⅤ. What are the advantages and disadvantages of BTS7960B?Ⅵ. How to optimize the BTS7960B... -
28 September 2023
MPSA56 PNP General Purpose Transistor: Features, Working Principle and Application
Ⅰ. Overview of MPSA56Ⅱ. Symbol and footprint of MPSA56Ⅲ. Technical parametersⅣ. Features of MPSA56Ⅴ. Pinout and package of MPSA56Ⅵ. How does MPSA56 work?Ⅶ. How does the MPSA56 transistor... -
28 September 2023
TIP35C Footprint, Package, Application and Other Details
Ⅰ. Overview of TIP35CⅡ. Symbol and footprint of TIP35CⅢ. Technical parametersⅣ. Features of TIP35CⅤ. Pinout and package of TIP35CⅥ. Working principle of TIP35C audio power amplifierⅦ. Application of...
Help you to save your cost and time.
Reliable package for your goods.
Fast Reliable Delivery to save time.
Quality premium after-sale service.