Texas Instruments CD4053BM96
- Part Number:
- CD4053BM96
- Manufacturer:
- Texas Instruments
- Ventron No:
- 3670909-CD4053BM96
- Description:
- 20-V, 2:1 (SPDT), 3-channel analog multiplexer with logic-level conversion
- Datasheet:
- cd4053b
Texas Instruments CD4053BM96 technical specifications, attributes, parameters and parts with similar specifications to Texas Instruments CD4053BM96.
- Factory Lead Time6 Weeks
- Lifecycle StatusACTIVE (Last Updated: 2 days ago)
- Contact PlatingTin
- MountSurface Mount
- Mounting TypeSurface Mount
- Package / Case16-SOIC (0.154, 3.90mm Width)
- Number of Pins16
- Weight141.690917mg
- Operating Temperature-55°C~125°C TA
- PackagingCut Tape (CT)
- JESD-609 Codee3
- Pbfree Codeyes
- Part StatusActive
- Moisture Sensitivity Level (MSL)1 (Unlimited)
- Number of Terminations16
- ECCN CodeEAR99
- Resistance240Ohm
- SubcategoryMultiplexer or Switches
- TechnologyCMOS
- Terminal FormGULL WING
- Peak Reflow Temperature (Cel)260
- Number of Functions3
- Supply Voltage5V
- Terminal Pitch1.27mm
- Base Part NumberCD4053
- OutputSEPARATE OUTPUT
- Pin Count16
- Operating Supply Voltage18V
- PolarityNon-Inverting
- Number of Channels2
- Number of Circuits3
- Max Supply Voltage20V
- Min Supply Voltage3V
- Analog IC - Other TypeSINGLE-ENDED MULTIPLEXER
- Operating Supply Current80nA
- Nominal Supply Current100μA
- Propagation Delay60 ns
- Quiescent Current80nA
- Turn On Delay Time720 ns
- Logic FunctionDemultiplexer, Multiplexer
- Number of Inputs6
- Voltage - Supply, Single/Dual (±)3V~20V ±2.5V~9V
- Supply TypeDual, Single
- Bandwidth30MHz
- Neg Supply Voltage-Nom (Vsup)-5V
- Turn-Off Delay Time450 ns
- Max Dual Supply Voltage9V
- On-State Resistance (Max)240Ohm
- Min Dual Supply Voltage2.5V
- Dual Supply Voltage5V
- Multiplexer/Demultiplexer Circuit2:1
- Off-state Isolation-Nom40 dB
- Current - Leakage (IS(off)) (Max)100nA
- Channel Capacitance (CS(off), CD(off))0.2pF 9pF
- On-state Resistance Match-Nom15Ohm
- Switch CircuitSPDT
- Channel-to-Channel Matching (ΔRon)5 Ω
- Crosstalk-40dB @ 6MHz
- SwitchingBREAK-BEFORE-MAKE
- Max Junction Temperature (Tj)150°C
- Drain to Source Resistance240Ohm
- Normal PositionNC
- Signal Current-Max0.01A
- On-State Resistance125Ohm
- Height1.75mm
- Length9.9mm
- Width3.91mm
- Thickness1.58mm
- Radiation HardeningNo
- REACH SVHCNo SVHC
- RoHS StatusROHS3 Compliant
- Lead FreeLead Free
CD4053BM96 Overview
Presented in 16-SOIC (0.154, 3.90mm Width), this electrical component is convenient for overseas shipping. This packaging method provides high reliability because it uses advanced packaging techniques. The multiplexer is located in Surface Mount. There is 2:1 ratio between the number of multiplexers and demultiplexers. The operating temperature is extended to around -55°C~125°C TA. 16 terminations have been made so far. As a result of its 2 channels, this electronic component provides high-quality output. If the voltage supply is 5V volts, the electrical component should be turned on and run. An injection of 16 pins is performed into the body of the electrical component. A SPDT switching circuit is used for these analog switches. A total of 3 circuits make up this switch device. Look for analog switch ic variants by searching with CD4053. Analog switches have 240Ohm internal resistance. You can find the functions of the 16 pins in the datasheets. A analogue multiplexer of this type is a Multiplexer or Switches. In a normalsituation, users should not supply the switches with voltage higher than 20V. Dual, Single supply type digital switch with a low cost. In order for the electronic part to function properly, the lowest voltage should be 3V. An operating current of 80nA would be sufficient for this switch device. If put voltage greater than 9V on the multiplexer, damage may be caused to the device. In the case of dual power supplies, you should connect at least 2.5V. There is an analog IC SINGLE-ENDED MULTIPLEXER integrated with this board. There are SEPARATE OUTPUT outputs on this analog switch ic. Operating voltages range from 18V. A 6 input needs to be operated. The data can be transferred over a wide range of bandwidths, called 30MHz bandwidths. There is 240Ohm Drain to Source resistance on this electronic part.
CD4053BM96 Features
2 Channels
Switch Circuit: SPDT
80nA Supply Current
Bandwidth: 30MHz
Drain-to-Source resistance: 240Ohm
CD4053BM96 Applications
There are a lot of Texas Instruments CD4053BM96 Analog Switches & Multiplexers ICs applications.
T1/E1 Terminals
Battery Powered Instruments
Channelized and Unchannelized DS3 applications
PDH Multiplexers
Avionics test equipment
Communications systems
Access Concentrators
65 V DACs
Avionics
Medical systems
Presented in 16-SOIC (0.154, 3.90mm Width), this electrical component is convenient for overseas shipping. This packaging method provides high reliability because it uses advanced packaging techniques. The multiplexer is located in Surface Mount. There is 2:1 ratio between the number of multiplexers and demultiplexers. The operating temperature is extended to around -55°C~125°C TA. 16 terminations have been made so far. As a result of its 2 channels, this electronic component provides high-quality output. If the voltage supply is 5V volts, the electrical component should be turned on and run. An injection of 16 pins is performed into the body of the electrical component. A SPDT switching circuit is used for these analog switches. A total of 3 circuits make up this switch device. Look for analog switch ic variants by searching with CD4053. Analog switches have 240Ohm internal resistance. You can find the functions of the 16 pins in the datasheets. A analogue multiplexer of this type is a Multiplexer or Switches. In a normalsituation, users should not supply the switches with voltage higher than 20V. Dual, Single supply type digital switch with a low cost. In order for the electronic part to function properly, the lowest voltage should be 3V. An operating current of 80nA would be sufficient for this switch device. If put voltage greater than 9V on the multiplexer, damage may be caused to the device. In the case of dual power supplies, you should connect at least 2.5V. There is an analog IC SINGLE-ENDED MULTIPLEXER integrated with this board. There are SEPARATE OUTPUT outputs on this analog switch ic. Operating voltages range from 18V. A 6 input needs to be operated. The data can be transferred over a wide range of bandwidths, called 30MHz bandwidths. There is 240Ohm Drain to Source resistance on this electronic part.
CD4053BM96 Features
2 Channels
Switch Circuit: SPDT
80nA Supply Current
Bandwidth: 30MHz
Drain-to-Source resistance: 240Ohm
CD4053BM96 Applications
There are a lot of Texas Instruments CD4053BM96 Analog Switches & Multiplexers ICs applications.
T1/E1 Terminals
Battery Powered Instruments
Channelized and Unchannelized DS3 applications
PDH Multiplexers
Avionics test equipment
Communications systems
Access Concentrators
65 V DACs
Avionics
Medical systems
CD4053BM96 More Descriptions
20-V, 2:1 (SPDT), 3-channel analog multiplexer with logic-level conversion 16-SOIC -55 to 125
Analog Multiplexer Triple 2:1 16-Pin SOIC T/R
Single-Ended Multiplexer, 3 Func, 3 Channel, CMOS, PDSO16
IC, ANALOG MUX/DMUX, TRI 2 X 1, SOIC-16
ANALOG MULTIPLEXER/DEMULTIPLEXERIC SWITCH SPDT X 3 240OHM 16SOIC
Logic - Signal Switches Triple 2-Ch Analog
IC MUX/DEMUX TRIPLE 2X1 16SOIC
CD4053B CMOS TRIPLE 2-CHANNEL AN
Analogue Mux/Demux, Triple, 2:1, Soic-16; Multiplexer Configuration:2:1; No. Of Circuits:3Circuits; On State Resistance Max:240Ohm; Supply Voltage Range:3V To 20V; Analogue Multiplexer Case:Soic; No. Of Pins:16Pins; Operating Rohs Compliant: Yes |TEXAS INSTRUMENTS CD4053BM96
Analog Multiplexer Triple 2:1 16-Pin SOIC T/R
Single-Ended Multiplexer, 3 Func, 3 Channel, CMOS, PDSO16
IC, ANALOG MUX/DMUX, TRI 2 X 1, SOIC-16
ANALOG MULTIPLEXER/DEMULTIPLEXER
Logic - Signal Switches Triple 2-Ch Analog
IC MUX/DEMUX TRIPLE 2X1 16SOIC
CD4053B CMOS TRIPLE 2-CHANNEL AN
Analogue Mux/Demux, Triple, 2:1, Soic-16; Multiplexer Configuration:2:1; No. Of Circuits:3Circuits; On State Resistance Max:240Ohm; Supply Voltage Range:3V To 20V; Analogue Multiplexer Case:Soic; No. Of Pins:16Pins; Operating Rohs Compliant: Yes |TEXAS INSTRUMENTS CD4053BM96
Popular Search Part Number
Related Keywords
Search Tags
Latest News
-
23 November 2023
OP07 Operational Amplifier Features, Pin Configuration and Application Scenarios
Ⅰ. Overview of OP07 operational amplifierⅡ. Features of OP07 operational amplifierⅢ. OP07 symbol, footprint and pin configurationⅣ. Working principle of OP07 operational amplifierⅤ. Differential amplifier circuit of OP07Ⅵ.... -
23 November 2023
AT89C52 Microcontroller Equivalents, Functions, Structure and Applications
Ⅰ. What is AT89C52 microcontroller?Ⅱ. What are the features of AT89C52 microcontroller?Ⅲ. AT89C52 symbol, footprint and pin configurationⅣ. Functions of AT89C52 microcontrollerⅤ. Structure of AT89C52 microcontrollerⅥ. What are... -
24 November 2023
6N136 High Speed Optocoupler Pin Configuration, Features and Working principle
Ⅰ. Overview of 6N136 optocouplerⅡ. Symbol, footprint and pin configuration of 6N136 optocouplerⅢ. Features of 6N136 optocouplerⅣ. Technical parameters of 6N136 optocouplerⅤ. Applications of 6N136 optocouplerⅥ. Working principle... -
24 November 2023
An Introduction to the PCA9685 16-Channel Servo Controller Module
Ⅰ. Overview of PCA9685Ⅱ. Manufacturer of PCA9685Ⅲ. Pin configuration of PCA9685Ⅳ. What are the features of PCA9685?Ⅴ. How does the PCA9685 work?Ⅵ. What are the applications of PCA9685?Ⅶ....
Help you to save your cost and time.
Reliable package for your goods.
Fast Reliable Delivery to save time.
Quality premium after-sale service.