Analog Devices Inc. AD8037ANZ
- Part Number:
- AD8037ANZ
- Manufacturer:
- Analog Devices Inc.
- Ventron No:
- 3192575-AD8037ANZ
- Description:
- IC OPAMP VFB 270MHZ 8DIP
- Datasheet:
- AD8037ANZ
Analog Devices Inc. AD8037ANZ technical specifications, attributes, parameters and parts with similar specifications to Analog Devices Inc. AD8037ANZ.
- Mounting TypeThrough Hole
- Package / Case8-DIP (0.300, 7.62mm)
- Surface MountNO
- Operating Temperature-40°C~85°C
- PackagingTube
- SeriesCLAMPIN™
- JESD-609 Codee3
- Pbfree Codeyes
- Part StatusObsolete
- Moisture Sensitivity Level (MSL)4 (72 Hours)
- Number of Terminations8
- Terminal FinishMATTE TIN
- SubcategoryOperational Amplifier
- Terminal PositionDUAL
- Peak Reflow Temperature (Cel)NOT APPLICABLE
- Number of Functions1
- Supply Voltage5V
- Terminal Pitch2.54mm
- Reach Compliance Codeunknown
- Time@Peak Reflow Temperature-Max (s)NOT APPLICABLE
- Pin Count8
- JESD-30 CodeR-PDIP-T8
- Number of Circuits1
- Current - Supply18.5mA
- Slew Rate1500V/μs
- Amplifier TypeVoltage Feedback
- Common Mode Rejection Ratio90 dB
- Current - Input Bias3μA
- Voltage - Supply, Single/Dual (±)±3V~6V
- Neg Supply Voltage-Nom (Vsup)-5V
- Supply Voltage Limit-Max6.3V
- Voltage - Input Offset2mV
- Current - Output / Channel70mA
- 3db Bandwidth270MHz
- Neg Supply Voltage-Max (Vsup)-6.3V
- Length9.88mm
- Height Seated (Max)5.33mm
- RoHS StatusROHS3 Compliant
AD8037ANZ Overview
A 8-DIP (0.300, 7.62mm) case is used to package the op amp. Voltage Feedback-type instrumentation amplifiers are used in this application. The case in which buffer amplifier is delivered is called a Tube case. It is estimated that there will be 8 terminations in the next few months. There are a total of 8 pins on this op amp. It is important to remember that this op amp should be operated at a voltage of 5V volts. It should be noted that this op amp is a type of Operational Amplifier device. It is recommended that this electronic component be mounted using the Through Hole mounting type. In terms of operating temperature, this instrumentation amplifier performs well at a temperature of about -40°C~85°C . On this instrumentation amplifier, there are 1 circuits that are connected together. As a recommendation, this electronic component should be used with a power supply that can deliver 18.5mA. The CLAMPIN™ indicates the series number of the op amp.
AD8037ANZ Features
8 Pins
supply voltage of 5V
AD8037ANZ Applications
There are a lot of Rochester Electronics, LLC
AD8037ANZ Instrumentational OP Amps applications.
Addition operation circuits
Subtraction operation circuits
single/dual op amp sum and difference circuits
Integrator circuits
Differentiator circuits
Logarithmic operation circuits
Exponential operation circuits
Multiplication circuits
Division circuits
Precision measurement
A 8-DIP (0.300, 7.62mm) case is used to package the op amp. Voltage Feedback-type instrumentation amplifiers are used in this application. The case in which buffer amplifier is delivered is called a Tube case. It is estimated that there will be 8 terminations in the next few months. There are a total of 8 pins on this op amp. It is important to remember that this op amp should be operated at a voltage of 5V volts. It should be noted that this op amp is a type of Operational Amplifier device. It is recommended that this electronic component be mounted using the Through Hole mounting type. In terms of operating temperature, this instrumentation amplifier performs well at a temperature of about -40°C~85°C . On this instrumentation amplifier, there are 1 circuits that are connected together. As a recommendation, this electronic component should be used with a power supply that can deliver 18.5mA. The CLAMPIN™ indicates the series number of the op amp.
AD8037ANZ Features
8 Pins
supply voltage of 5V
AD8037ANZ Applications
There are a lot of Rochester Electronics, LLC
AD8037ANZ Instrumentational OP Amps applications.
Addition operation circuits
Subtraction operation circuits
single/dual op amp sum and difference circuits
Integrator circuits
Differentiator circuits
Logarithmic operation circuits
Exponential operation circuits
Multiplication circuits
Division circuits
Precision measurement
AD8037ANZ More Descriptions
ROHS3Compliant R-PDIP-T8 MATTE TIN Tube op amp amplifier circuit 9.88mm 3muA -6.3V 270MHz
Operational Amplifier, 1 Func, 10000uV Offset-Max, Hybrid, PDIP8
IC, AMP, 240MHZ CLAMP, , 8037, DIP8; Op Amp Type:Low Distortion; No. of Amplifiers:1; Bandwidth:270MHz; Slew Rate:1500Vµs; Supply Voltage Range:± 3V to ± 6V; Amplifier Case Style:DIP; No. of Pins:8; Operating Temperature Range:-40°C to 85°C; Amplifier Type:Operational; Base Number:8037; Gain Bandwidth:270MHz; Gain Bandwidth:240MHz; IC Generic Number:8037; Input Offset Voltage Max:10mV; Logic Function Number:8037; Operating Temperature Max:85°C; Operating Temperature Min:-40°C; Operational Amplifier Features:Low Distortion; Package / Case:DIP; Slew Rate:1500V/µs; Supply Voltage Nom:5V; Supply Voltage Max:6V; Supply Voltage Min:3V; Termination Type:Through Hole
The AD8036 and AD8037 are wide bandwidth, low distortion clamping amplifiers. The AD8036 is unity gain stable. The AD8037 is stable at a gain of two or greater. These devices allow the designer to specify a high (VCH) and low (VCL) output clamp voltage. The output signal will clamp at these specified levels. Utilizing a unique patent pending CLAMPIN™ input clamp architecture, the AD8036 and AD8037 offer a 10 ×improvement in clamp performance compared to traditional out-V put clamping devices. In particular, clamp error is typically 3 mV or less and distortion in the clamp region is minimized. This product can be used as a classical op amp or a clamp amplifier where a high and low output voltage are specified. The AD8036 and AD8037, which utilize a voltage feedback architecture, meet the requirements of many applications which previously depended on current feedback amplifiers. The AD8036 and AD8037 exhibit an exceptionally fast and accurate pulse response (16 ns to 0.01%), extremely wide small-signal and large-signal bandwidths and ultralow distortion. The AD8036 achieves -66 dBc at 20 MHz, and 240 MHz small-signal and 195 MHz large-signal bandwidths. The AD8036 and AD8037's recover from 2× clamp overdrive within 1.5 ns. These characteristics position the AD8036/AD8037 ideally for driving as well as buffering flash and high resolution ADCs. In addition to traditional output clamp amplifier applications, the input clamp architecture supports the clamp levels as additional inputs to the amplifier. As such, in addition to static dc clamp levels, signals with speeds up to 240 MHz can be applied to the clamp pins. The clamp values can also be set to any value within the output voltage range provided that VH is greater that VL. Due to these clamp characteristics, the AD8036 and AD8037 can be used in nontraditional applications such as a full-wave rectifier, a pulse generator, or an amplitude modulator. These novel applications are only examples of some of the diverse applications which can be designed with input clamps. The AD8036 is offered in chips, industrial (-40°C to 85°) and military (-55°C to 125°C) package temperature ranges and the AD8037 in industrial. Industrial versions are available in plastic DIP and SOIC; MIL versions are packaged in cerdip. An evaluation board is available for this product and may be ordered using the following product number: AD8036-EB and AD8037-EB. Schematic and layout for this evaluation board is contained in the product datasheet.
Operational Amplifier, 1 Func, 10000uV Offset-Max, Hybrid, PDIP8
IC, AMP, 240MHZ CLAMP, , 8037, DIP8; Op Amp Type:Low Distortion; No. of Amplifiers:1; Bandwidth:270MHz; Slew Rate:1500Vµs; Supply Voltage Range:± 3V to ± 6V; Amplifier Case Style:DIP; No. of Pins:8; Operating Temperature Range:-40°C to 85°C; Amplifier Type:Operational; Base Number:8037; Gain Bandwidth:270MHz; Gain Bandwidth:240MHz; IC Generic Number:8037; Input Offset Voltage Max:10mV; Logic Function Number:8037; Operating Temperature Max:85°C; Operating Temperature Min:-40°C; Operational Amplifier Features:Low Distortion; Package / Case:DIP; Slew Rate:1500V/µs; Supply Voltage Nom:5V; Supply Voltage Max:6V; Supply Voltage Min:3V; Termination Type:Through Hole
The AD8036 and AD8037 are wide bandwidth, low distortion clamping amplifiers. The AD8036 is unity gain stable. The AD8037 is stable at a gain of two or greater. These devices allow the designer to specify a high (VCH) and low (VCL) output clamp voltage. The output signal will clamp at these specified levels. Utilizing a unique patent pending CLAMPIN™ input clamp architecture, the AD8036 and AD8037 offer a 10 ×improvement in clamp performance compared to traditional out-V put clamping devices. In particular, clamp error is typically 3 mV or less and distortion in the clamp region is minimized. This product can be used as a classical op amp or a clamp amplifier where a high and low output voltage are specified. The AD8036 and AD8037, which utilize a voltage feedback architecture, meet the requirements of many applications which previously depended on current feedback amplifiers. The AD8036 and AD8037 exhibit an exceptionally fast and accurate pulse response (16 ns to 0.01%), extremely wide small-signal and large-signal bandwidths and ultralow distortion. The AD8036 achieves -66 dBc at 20 MHz, and 240 MHz small-signal and 195 MHz large-signal bandwidths. The AD8036 and AD8037's recover from 2× clamp overdrive within 1.5 ns. These characteristics position the AD8036/AD8037 ideally for driving as well as buffering flash and high resolution ADCs. In addition to traditional output clamp amplifier applications, the input clamp architecture supports the clamp levels as additional inputs to the amplifier. As such, in addition to static dc clamp levels, signals with speeds up to 240 MHz can be applied to the clamp pins. The clamp values can also be set to any value within the output voltage range provided that VH is greater that VL. Due to these clamp characteristics, the AD8036 and AD8037 can be used in nontraditional applications such as a full-wave rectifier, a pulse generator, or an amplitude modulator. These novel applications are only examples of some of the diverse applications which can be designed with input clamps. The AD8036 is offered in chips, industrial (-40°C to 85°) and military (-55°C to 125°C) package temperature ranges and the AD8037 in industrial. Industrial versions are available in plastic DIP and SOIC; MIL versions are packaged in cerdip. An evaluation board is available for this product and may be ordered using the following product number: AD8036-EB and AD8037-EB. Schematic and layout for this evaluation board is contained in the product datasheet.
Popular Search Part Number
Related Keywords
Search Tags
Latest News
-
09 October 2023
Lithium CR2450 Battery Symbol, Equivalent, Specifications and Uses
Ⅰ. What is CR2450 battery?Ⅱ. CR2450 symbol and footprintⅢ. Specifications of CR2450 batteryⅣ. What are the features of CR2450 battery?Ⅴ. What are the uses of CR2450 battery?Ⅵ. What... -
10 October 2023
Get to know the Lithium Coin Cell CR2354
Ⅰ. What is a button battery?Ⅱ. What is CR2354 battery?Ⅲ. Dimensions of CR2354 batteryⅣ. Specifications of CR2354 batteryⅤ. Features of CR2354 batteryⅥ. What are the uses of CR2354... -
10 October 2023
IRF4905 Mosfet Transistor: Equivalent, Features, Working Principle and Other Details
Ⅰ. Overview of IRF4905Ⅱ. Pin configuration, symbol and footprint of IRF4905Ⅲ. Technical parameters of IRF4905Ⅳ. Features of IRF4905Ⅴ. Working principle of IRF4905Ⅵ. Dimensions and package of IRF4905Ⅶ. How... -
11 October 2023
STM8S103F3P6 Microcontroller Equivalent, Features and Pinout Configuration
Ⅰ. What is STM8S103F3P6 microcontroller?Ⅱ. Symbol and footprint of STM8S103F3P6Ⅲ. Technical parameters of STM8S103F3P6Ⅳ. Features of STM8S103F3P6Ⅴ. Size and package of STM8S103F3P6Ⅵ. Electrical characteristics of STM8S103F3P6Ⅶ. Pinout configuration...
Help you to save your cost and time.
Reliable package for your goods.
Fast Reliable Delivery to save time.
Quality premium after-sale service.