Analog Devices Inc. AD605BRZ-RL
- Part Number:
- AD605BRZ-RL
- Manufacturer:
- Analog Devices Inc.
- Ventron No:
- 3698389-AD605BRZ-RL
- Description:
- IC OPAMP VGA 40MHZ 16SOIC
- Datasheet:
- AD605BRZ-RL
Analog Devices Inc. AD605BRZ-RL technical specifications, attributes, parameters and parts with similar specifications to Analog Devices Inc. AD605BRZ-RL.
- Contact PlatingTin
- MountSurface Mount
- Mounting TypeSurface Mount
- Package / Case16-SOIC (0.154, 3.90mm Width)
- Number of Pins16
- Weight665.986997mg
- Operating Temperature-40°C~85°C
- PackagingTape & Reel (TR)
- SeriesX-AMP®
- JESD-609 Codee3
- Pbfree Codeyes
- Part StatusObsolete
- Moisture Sensitivity Level (MSL)1 (Unlimited)
- Number of Terminations16
- ECCN CodeEAR99
- Resistance175Ohm
- SubcategoryOther Analog ICs
- Terminal PositionDUAL
- Terminal FormGULL WING
- Peak Reflow Temperature (Cel)260
- Number of Functions2
- Supply Voltage5V
- Base Part NumberAD605
- Pin Count16
- Operating Supply Voltage5V
- Number of Elements2
- Power Supplies5V
- Number of Circuits2
- Analog IC - Other TypeANALOG CIRCUIT
- Operating Supply Current18mA
- Slew Rate170V/μs
- Amplifier TypeVariable Gain
- Common Mode Rejection Ratio20 dB
- Current - Input Bias400nA
- Voltage - Supply, Single/Dual (±)4.5V~5.5V
- Output Current per Channel40mA
- Gain Bandwidth Product40MHz
- Voltage Gain34dB
- Length9.9mm
- Height Seated (Max)1.75mm
- Radiation HardeningNo
- RoHS StatusROHS3 Compliant
- Lead FreeContains Lead
AD605BRZ-RL Overview
Packaging for the buffer amplifier is in the form of a 16-SOIC (0.154, 3.90mm Width) case. A Variable Gain-type buffer amplifier is shown here. There is a Tape & Reel (TR) case that is delivered with the instrumentation amplifiers. A total of 16 terminations have been reported in the past few weeks. Buffer amplifier has a total of 16 pins on it. I would like you to keep in mind that this buffer amplifier needs to be run at a voltage of 5V. In more specific terms, this linear amplifier can be categoriOther Analog ICsed as a Other Analog ICs-type device. An 16-pin op amp ic is included in the package. For this electrical component, the recommended mounting type is Surface Mount, which is the most common. The buffer amplifier functions well at -40°C~85°C as far as operating temperature is concerned. Using a supply current of 18mA , this buffer op amp will be able to operate. 34dB should be the voltage gain. The buffer amp consists of 2 circuits in total. There is an operating supply voltage rating of 2 for this operational amplifier, which is rated at the manufacturer. The operating supply voltage of the buffer op amp is rated at 5V. The X-AMP® stands for the buffer op amp's serial number. It is recommended to keep the instrumentation amplifier resistance within the range of 175Ohm. An analog IC that is also used in this instrumentation amplifier is referred to as the ANALOG CIRCUIT type.
AD605BRZ-RL Features
16 Pins
supply voltage of 5V
34dB voltage gain
Resistance of 175Ohm
AD605BRZ-RL Applications
There are a lot of Analog Devices Inc.
AD605BRZ-RL Instrumentational OP Amps applications.
single/dual op amp sum and difference circuits
Integrator circuits
Differentiator circuits
Logarithmic operation circuits
Exponential operation circuits
Multiplication circuits
Division circuits
Precision measurement
Power control
Information processing
Packaging for the buffer amplifier is in the form of a 16-SOIC (0.154, 3.90mm Width) case. A Variable Gain-type buffer amplifier is shown here. There is a Tape & Reel (TR) case that is delivered with the instrumentation amplifiers. A total of 16 terminations have been reported in the past few weeks. Buffer amplifier has a total of 16 pins on it. I would like you to keep in mind that this buffer amplifier needs to be run at a voltage of 5V. In more specific terms, this linear amplifier can be categoriOther Analog ICsed as a Other Analog ICs-type device. An 16-pin op amp ic is included in the package. For this electrical component, the recommended mounting type is Surface Mount, which is the most common. The buffer amplifier functions well at -40°C~85°C as far as operating temperature is concerned. Using a supply current of 18mA , this buffer op amp will be able to operate. 34dB should be the voltage gain. The buffer amp consists of 2 circuits in total. There is an operating supply voltage rating of 2 for this operational amplifier, which is rated at the manufacturer. The operating supply voltage of the buffer op amp is rated at 5V. The X-AMP® stands for the buffer op amp's serial number. It is recommended to keep the instrumentation amplifier resistance within the range of 175Ohm. An analog IC that is also used in this instrumentation amplifier is referred to as the ANALOG CIRCUIT type.
AD605BRZ-RL Features
16 Pins
supply voltage of 5V
34dB voltage gain
Resistance of 175Ohm
AD605BRZ-RL Applications
There are a lot of Analog Devices Inc.
AD605BRZ-RL Instrumentational OP Amps applications.
single/dual op amp sum and difference circuits
Integrator circuits
Differentiator circuits
Logarithmic operation circuits
Exponential operation circuits
Multiplication circuits
Division circuits
Precision measurement
Power control
Information processing
AD605BRZ-RL More Descriptions
SP Amp Variable Gain Amp Dual 5.5V 16-Pin SOIC N T/R
Special Purpose Amplifiers Dual Low Noise SGL-Supply VGA
The AD605 is a low noise, accurate, dual-channel, linear-in-dB variable gain amplifier (VGA), optimized for any application requiring high performance, wide bandwidth variable gain control. Operating from a single 5 V supply, the AD605 provides differential inputs and unipolar gain control for ease of use. Added flexibility is achieved with a user-determined gain range and an external reference input that provide user-determined gain scaling (dB/V). The high performance linear-in-dB response of the AD605 is achieved with the differential input, single-supply, exponential amplifier (DSX-AMP) architecture. Each of the DSX-AMPs comprises a variable attenuator of 0 dB to -48.4 dB followed by a high speed, fixed-gain amplifier. The attenuator is based on a 7-stage R-1.5R ladder network. The attenuation between tap points is 6.908 dB, and 48.360 dB for the entire ladder network. The DSX-AMP architecture results in 1.8 nV/vHz input noise spectral density and accepts a ±2.0 V input signal when VOCM is biased at VP/2. Each independent channel of the AD605 provides a gain range of 48 dB that can be optimized for the application. Gain ranges between -14 dB to 34 dB and 0 dB to 48 dB can be selected by a single resistor between Pin FBK and Pin OUT. The lower and upper gain ranges are determined by shorting Pin FBK to Pin OUT or leaving Pin FBK unconnected, respectively. The two channels of the AD605 can be cascaded to provide 96 dB of very accurate gain range in a monolithic package. The gain control interface provides an input resistance of approximately 2 MO and scale factors from 20 dB/V to 30 dB/V for a VREF input voltage of 2.5 V to 1.67 V, respectively. Note that scale factors up to 40 dB/V are achievable with reduced accuracy for scales above 30 dB/V. The gain scales linearly in dB with control voltages (VGN) of 0.4 V to 2.4 V for the 20 dB/V scale and 0.20 V to 1.20 V for the 40 dB/V scale. When VGN is <50 mV, the amplifier is powered down to draw 1.9 mA. Under normal operation, the quiescent supply current of each amplifier channel is only 18 mA. The AD605 is available in a 16-lead PDIP and a 16-lead SOIC_N package and is guaranteed for operation over the -40°C to 85°C temperature range. Applications Ultrasound and sonar time-gain controls High performance AGC systems Signal measurement Data Sheet, Rev. E, 5/07
Special Purpose Amplifiers Dual Low Noise SGL-Supply VGA
The AD605 is a low noise, accurate, dual-channel, linear-in-dB variable gain amplifier (VGA), optimized for any application requiring high performance, wide bandwidth variable gain control. Operating from a single 5 V supply, the AD605 provides differential inputs and unipolar gain control for ease of use. Added flexibility is achieved with a user-determined gain range and an external reference input that provide user-determined gain scaling (dB/V). The high performance linear-in-dB response of the AD605 is achieved with the differential input, single-supply, exponential amplifier (DSX-AMP) architecture. Each of the DSX-AMPs comprises a variable attenuator of 0 dB to -48.4 dB followed by a high speed, fixed-gain amplifier. The attenuator is based on a 7-stage R-1.5R ladder network. The attenuation between tap points is 6.908 dB, and 48.360 dB for the entire ladder network. The DSX-AMP architecture results in 1.8 nV/vHz input noise spectral density and accepts a ±2.0 V input signal when VOCM is biased at VP/2. Each independent channel of the AD605 provides a gain range of 48 dB that can be optimized for the application. Gain ranges between -14 dB to 34 dB and 0 dB to 48 dB can be selected by a single resistor between Pin FBK and Pin OUT. The lower and upper gain ranges are determined by shorting Pin FBK to Pin OUT or leaving Pin FBK unconnected, respectively. The two channels of the AD605 can be cascaded to provide 96 dB of very accurate gain range in a monolithic package. The gain control interface provides an input resistance of approximately 2 MO and scale factors from 20 dB/V to 30 dB/V for a VREF input voltage of 2.5 V to 1.67 V, respectively. Note that scale factors up to 40 dB/V are achievable with reduced accuracy for scales above 30 dB/V. The gain scales linearly in dB with control voltages (VGN) of 0.4 V to 2.4 V for the 20 dB/V scale and 0.20 V to 1.20 V for the 40 dB/V scale. When VGN is <50 mV, the amplifier is powered down to draw 1.9 mA. Under normal operation, the quiescent supply current of each amplifier channel is only 18 mA. The AD605 is available in a 16-lead PDIP and a 16-lead SOIC_N package and is guaranteed for operation over the -40°C to 85°C temperature range. Applications Ultrasound and sonar time-gain controls High performance AGC systems Signal measurement Data Sheet, Rev. E, 5/07
Popular Search Part Number
Related Keywords
Search Tags
Latest News
-
16 January 2024
PDIUSBD12 Structure, Pin Configuration, Characteristics and Applications
Ⅰ. Overview of PDIUSBD12Ⅱ. Design of PDIUSBD12Ⅲ. Internal structure of PDIUSBD12Ⅳ. Pin configuration of PDIUSBD12Ⅴ. What are the characteristics of PDIUSBD12?Ⅵ. PDIUSBD12 instructionsⅦ. What are the applications of... -
17 January 2024
MCF5282CVM66 Microcontroller Replacements, Structure, Working Principle and Other Details
Ⅰ. MCF5282CVM66 overviewⅡ. Structure and working principle of MCF5282CVM66Ⅲ. Specifications of MCF5282CVM66Ⅳ. What are the advantages and disadvantages of MCF5282CVM66?Ⅴ. Purpose of MCF5282CVM66Ⅵ. Market trend of MCF5282CVM66Ⅶ. Precautions... -
17 January 2024
DS18B20 Digital Temperature Sensor Structure, Features, Applications and More
Ⅰ. What is DS18B20?Ⅱ. Internal structure of DS18B20Ⅲ. Features of DS18B20 sensorⅣ. How does DS18B20 work?Ⅴ. Symbol, footprint and pin configuration of DS18B20Ⅵ. Driving principle of DS18B20Ⅶ. Where... -
18 January 2024
What is the BTN8982TA Bridge and How Does it Work?
Ⅰ. Introduction to BTN8982TAⅡ. Block diagram of BTN8982TAⅢ. Specifications of BTN8982TAⅣ. Working principle of BTN8982TAⅤ. BTN8982TA symbol, footprint and pin configurationⅥ. Features of BTN8982TAⅦ. Application fields of BTN8982TABTN8982TA...
Help you to save your cost and time.
Reliable package for your goods.
Fast Reliable Delivery to save time.
Quality premium after-sale service.