Texas Instruments 74FCT162500CTPVCG4
- Part Number:
- 74FCT162500CTPVCG4
- Manufacturer:
- Texas Instruments
- Ventron No:
- 3226606-74FCT162500CTPVCG4
- Description:
- IC UNIV BUS TXRX 18BIT 56SSOP
- ECAD Model:
-
- Datasheet:
- CY74FCT16(2)500T
Texas Instruments 74FCT162500CTPVCG4 technical specifications, attributes, parameters and parts with similar specifications to Texas Instruments 74FCT162500CTPVCG4.
- MountSurface Mount
- Mounting TypeSurface Mount
- Package / Case56-BSSOP (0.295, 7.50mm Width)
- Number of Pins56
- Operating Temperature-40°C~85°C
- PackagingTube
- Series74FCT
- Pbfree Codeyes
- Part StatusObsolete
- Moisture Sensitivity Level (MSL)1 (Unlimited)
- Number of Terminations56
- HTS Code8542.39.00.01
- TechnologyCMOS
- Voltage - Supply4.5V~5.5V
- Terminal PositionDUAL
- Terminal FormGULL WING
- Peak Reflow Temperature (Cel)NOT SPECIFIED
- Number of Functions1
- Supply Voltage5V
- Terminal Pitch0.635mm
- Reach Compliance Codeunknown
- Reflow Temperature-Max (s)NOT SPECIFIED
- Base Part Number74FCT162500
- Pin Count56
- Qualification StatusNot Qualified
- PolarityNon-Inverting
- Supply Voltage-Max (Vsup)5.5V
- Power Supplies5V
- Supply Voltage-Min (Vsup)4.5V
- Number of Circuits18-Bit
- Number of Ports2
- Number of Bits18
- Propagation Delay5.3 ns
- FamilyFCT
- Logic FunctionTransceiver
- Output Characteristics3-STATE WITH SERIES RESISTOR
- Current - Output High, Low24mA 24mA
- Logic TypeUniversal Bus Transceiver
- Max I(ol)0.064 A
- Trigger TypeNEGATIVE EDGE
- Control TypeINDEPENDENT CONTROL
- Count DirectionBIDIRECTIONAL
- TranslationN/A
- Height Seated (Max)2.79mm
- Length18.415mm
- Width7.49mm
- RoHS StatusROHS3 Compliant
74FCT162500CTPVCG4 Overview
As part of 56-BSSOP (0.295, 7.50mm Width), it is embedded. Packaged in the manner of Tube. In order to achieve the high level of flexibility that it possesses, 18-Bit circuits are used. A Universal Bus Transceiver logic type is used in this electrical device. Surface Mount is pointing towards the electronic part. Operating temperatures should be higher than -40°C~85°C. It features maximum design flexibility thanks to its High/Low output current. It is a type of FPGA that belongs to the 74FCT series of FPGAs. It operates with a supply voltage of 4.5V~5.5V. As it belongs to the 74FCT162500 family, it should be taken into consideration. The 56 termination is a practice in which a transmission line is terminated with an impedance matching device at the end of the line in order to match the characteristic impedance of the line. In order to function normally, the supply voltage should be higher than 5V. This device is equipped with 56 pins. An electronic part designed with 18 Bits is used in this product. It is possible to terminate a transmission line with a device that matches the line's characteristic impedance, known as 2 terminations. In this case, the electronic part is mounted in the direction of Surface Mount. A 56-pin is used for its design. The electronic device in question belongs to the FCT family of electronic devices. The maximal supply voltage (Vsup) reaches 5.5V. The supply voltage (Vsup) should be greater than 4.5V. A 5V power supply is used to operate it. NEGATIVE EDGE is used with the trigger.
74FCT162500CTPVCG4 Features
56-BSSOP (0.295, 7.50mm Width) package
74FCT series
74FCT162500 family
56 pin count
56 pins
5V power supplies
74FCT162500CTPVCG4 Applications
There are a lot of Texas Instruments 74FCT162500CTPVCG4 Universal Bus Functions applications.
Test and Measurement
Calculator
CMOS circuitry
Electronic and electrical project circuits
Refrigerator
Disk read-write IC
Digital watch
Industrial Controls
Hair dryer
Automatic watering system
As part of 56-BSSOP (0.295, 7.50mm Width), it is embedded. Packaged in the manner of Tube. In order to achieve the high level of flexibility that it possesses, 18-Bit circuits are used. A Universal Bus Transceiver logic type is used in this electrical device. Surface Mount is pointing towards the electronic part. Operating temperatures should be higher than -40°C~85°C. It features maximum design flexibility thanks to its High/Low output current. It is a type of FPGA that belongs to the 74FCT series of FPGAs. It operates with a supply voltage of 4.5V~5.5V. As it belongs to the 74FCT162500 family, it should be taken into consideration. The 56 termination is a practice in which a transmission line is terminated with an impedance matching device at the end of the line in order to match the characteristic impedance of the line. In order to function normally, the supply voltage should be higher than 5V. This device is equipped with 56 pins. An electronic part designed with 18 Bits is used in this product. It is possible to terminate a transmission line with a device that matches the line's characteristic impedance, known as 2 terminations. In this case, the electronic part is mounted in the direction of Surface Mount. A 56-pin is used for its design. The electronic device in question belongs to the FCT family of electronic devices. The maximal supply voltage (Vsup) reaches 5.5V. The supply voltage (Vsup) should be greater than 4.5V. A 5V power supply is used to operate it. NEGATIVE EDGE is used with the trigger.
74FCT162500CTPVCG4 Features
56-BSSOP (0.295, 7.50mm Width) package
74FCT series
74FCT162500 family
56 pin count
56 pins
5V power supplies
74FCT162500CTPVCG4 Applications
There are a lot of Texas Instruments 74FCT162500CTPVCG4 Universal Bus Functions applications.
Test and Measurement
Calculator
CMOS circuitry
Electronic and electrical project circuits
Refrigerator
Disk read-write IC
Digital watch
Industrial Controls
Hair dryer
Automatic watering system
74FCT162500CTPVCG4 More Descriptions
IC UNIV BUS TXRX 18BIT 56SSOP
16 BIT REG TRANSCEIVERContact for details
These 18-bit universal bus transceivers can be operated in transparent, latched, or clock modes by combining D-type latches and D-type flip-flops. Data flow in each direction is controlled by output-enable (OEAB and OEBA), latch enable (LEAB and LEBA), and clock inputs (CLKAB and CLKBA) inputs. For A-to-B data flow, the device operates in transparent mode when LEAB is HIGH. When LEAB is LOW, the A data is latched if CLKAB is held at a HIGH or LOWlogic level. If LEAB is LOW, the A bus data is stored in the latch/flip-flop on the HIGH-to-LOWtransition of CLKAB. OEAB performs the output enable function on the B port. Data flow from B-to-A is similar to that of A-to-B and is controlled by OEBA, LEBA, and LKBA. This device is fully specified for partial-power-down applications using Ioff. The Ioff circuitry disables the outputs, preventing damaging current backflow through the device when it is powered down. The CY74FCT16500T is ideally suited for driving high-capacitance loads and low-impedance backplanes. The CY74FCT162500T has 24-mA balanced output drivers with current limiting resistors in the outputs. This reduces the need for external terminating resistors and provides for minimal undershoot and reduced ground bounce. The CY74FCT162500T is ideal for driving transmission lines.
16 BIT REG TRANSCEIVER
These 18-bit universal bus transceivers can be operated in transparent, latched, or clock modes by combining D-type latches and D-type flip-flops. Data flow in each direction is controlled by output-enable (OEAB and OEBA), latch enable (LEAB and LEBA), and clock inputs (CLKAB and CLKBA) inputs. For A-to-B data flow, the device operates in transparent mode when LEAB is HIGH. When LEAB is LOW, the A data is latched if CLKAB is held at a HIGH or LOWlogic level. If LEAB is LOW, the A bus data is stored in the latch/flip-flop on the HIGH-to-LOWtransition of CLKAB. OEAB performs the output enable function on the B port. Data flow from B-to-A is similar to that of A-to-B and is controlled by OEBA, LEBA, and LKBA. This device is fully specified for partial-power-down applications using Ioff. The Ioff circuitry disables the outputs, preventing damaging current backflow through the device when it is powered down. The CY74FCT16500T is ideally suited for driving high-capacitance loads and low-impedance backplanes. The CY74FCT162500T has 24-mA balanced output drivers with current limiting resistors in the outputs. This reduces the need for external terminating resistors and provides for minimal undershoot and reduced ground bounce. The CY74FCT162500T is ideal for driving transmission lines.
Popular Search Part Number
Related Keywords
Search Tags
Latest News
-
12 September 2023
The Difference Between L293D and L298N
In this article we will explore the main differences between the L293D and L298N motor drivers. Both motor drives have their own unique features and applications. Understanding the... -
12 September 2023
Comprehensive Analysis of CR123A battery: Features, Applications and Purchase
Ⅰ. CR123A overviewThe CR123A battery, classified under the non-rechargeable (primary) category, is a high-performance power source with distinct specifications. Featuring a robust lithium manganese composition, it boasts a... -
13 September 2023
AT89S52-24PU Microcontroller Equivalent, Features and Working Principle
Ⅰ. AT89S52-24PU overviewAT89S52 is a low-voltage, high-performance 8-bit CMOS microcontroller with 8K bytes of in-circuit programmable flash memory (ISP). AT89S52 is a high-density non-volatile memory compatible with the... -
13 September 2023
The Difference Between CR2016 and CR2032 Button Batteries
Although CR2032 and CR2016 batteries are common coin-type batteries with similar appearance and the same voltage, they have obvious differences in power capacity and size. Below we will...
Help you to save your cost and time.
Reliable package for your goods.
Fast Reliable Delivery to save time.
Quality premium after-sale service.