Texas Instruments TL082CM
- Part Number:
- TL082CM
- Manufacturer:
- Texas Instruments
- Ventron No:
- 3193994-TL082CM
- Description:
- IC OPAMP JFET 4MHZ 8SOIC
- ECAD Model:
-
- Datasheet:
- TL082CM
Texas Instruments TL082CM technical specifications, attributes, parameters and parts with similar specifications to Texas Instruments TL082CM.
- Mounting TypeSurface Mount
- Package / Case8-SOIC (0.154, 3.90mm Width)
- Surface MountYES
- Number of Pins8
- Operating Temperature0°C~70°C
- PackagingTube
- SeriesBI-FET II™
- JESD-609 Codee0
- Pbfree Codeno
- Part StatusObsolete
- Moisture Sensitivity Level (MSL)1 (Unlimited)
- Number of Terminations8
- ECCN CodeEAR99
- Terminal FinishTin/Lead (Sn/Pb)
- SubcategoryOperational Amplifier
- TechnologyBIPOLAR
- Terminal PositionDUAL
- Terminal FormGULL WING
- Peak Reflow Temperature (Cel)235
- Number of Functions2
- Supply Voltage15V
- Base Part NumberTL082
- Pin Count8
- Operating Supply Voltage18V
- Number of Elements2
- Power Supplies-15V
- Operating Supply Current3.6mA
- Nominal Supply Current3.6mA
- Output Current17mA
- Slew Rate13V/μs
- ArchitectureVOLTAGE-FEEDBACK
- Amplifier TypeJ-FET
- Common Mode Rejection Ratio70 dB
- Current - Input Bias50pA
- Voltage - Supply, Single/Dual (±)10V~30V ±5V~18V
- Input Offset Voltage (Vos)15mV
- Neg Supply Voltage-Nom (Vsup)-15V
- Unity Gain BW-Nom4000 kHz
- Voltage Gain100dB
- Average Bias Current-Max (IIB)0.0004μA
- Power Supply Rejection Ratio (PSRR)70dB
- Low-OffsetNO
- Frequency CompensationYES
- Voltage - Input Offset5mV
- Low-BiasYES
- Bias Current-Max (IIB) @25C0.0004μA
- Nominal Gain Bandwidth Product4MHz
- Max I/O Voltage15mV
- Input Offset Current-Max (IIO)0.004μA
- Height Seated (Max)1.75mm
- Length4.9mm
- Radiation HardeningNo
- RoHS StatusNon-RoHS Compliant
- Lead FreeContains Lead
TL082CM Overview
In the package, you will find a 8-SOIC (0.154, 3.90mm Width)-case to contain the op amp ic. A J-FET-type buffer amplifier is shown here. A Tube case is used for delivering the op amp. A total of 8 terminations have been reported in the past few weeks. A total of 8 pins are located on this board. This linear amplifier should be powered by an 15V battery. I would like to specify that this buffer amplifier belongs to the Operational Amplifier-type of devices. An 8-pin op amp ic is included in the package. There is an input offset voltage of 15mV for this buffer op amp. For this electrical component, Surface Mount is the recommended mounting type. It is recommended that this op amp ic be operated at a temperature no higher than 0°C~70°C for optimal performance. This op amp can operate from a supply current at 3.6mA. Voltage gain should remain at 100dB. The op amp is rated for an operating supply voltage of 2. The operating supply voltage of instrumentation amplifier is rated 18V voltage. The BI-FET II? represents the op amp's series number.
TL082CM Features
8 Pins
supply voltage of 15V
100dB voltage gain
TL082CM Applications
There are a lot of Texas Instruments TL082CM Instrumentational OP Amps applications.
Mobile phone
Oscilloscopes
Proportional operation circuits
Wireless base stations
Precision measurement
Portable docking station
Subtraction operation circuits
Computer workstations
Signal transformation
Power transmission
In the package, you will find a 8-SOIC (0.154, 3.90mm Width)-case to contain the op amp ic. A J-FET-type buffer amplifier is shown here. A Tube case is used for delivering the op amp. A total of 8 terminations have been reported in the past few weeks. A total of 8 pins are located on this board. This linear amplifier should be powered by an 15V battery. I would like to specify that this buffer amplifier belongs to the Operational Amplifier-type of devices. An 8-pin op amp ic is included in the package. There is an input offset voltage of 15mV for this buffer op amp. For this electrical component, Surface Mount is the recommended mounting type. It is recommended that this op amp ic be operated at a temperature no higher than 0°C~70°C for optimal performance. This op amp can operate from a supply current at 3.6mA. Voltage gain should remain at 100dB. The op amp is rated for an operating supply voltage of 2. The operating supply voltage of instrumentation amplifier is rated 18V voltage. The BI-FET II? represents the op amp's series number.
TL082CM Features
8 Pins
supply voltage of 15V
100dB voltage gain
TL082CM Applications
There are a lot of Texas Instruments TL082CM Instrumentational OP Amps applications.
Mobile phone
Oscilloscopes
Proportional operation circuits
Wireless base stations
Precision measurement
Portable docking station
Subtraction operation circuits
Computer workstations
Signal transformation
Power transmission
TL082CM More Descriptions
Wide Bandwidth Dual JFET Input Operational Amplifier 8-SOIC 0 to 70
Operational Amplifier, 2 Func, 20000uV Offset-Max, BIPolar, PDSO8
These devices are low cost, high speed, dual JFET input operational amplifiers with an internally trimmed input offset voltage (BI-FET II(TM) technology). They require low supply current yet maintain a large gain bandwidth product and fast slew rate. In addition, well matched high voltage JFET input devices provide very low input bias and offset currents. The TL082 is pin compatible with the standard LM1558 allowing designers to immediately upgrade the overall performance of existing LM1558 and most LM358 designs. These amplifiers may be used in applications such as high speed integrators, fast D/A converters, sample and hold circuits and many other circuits requiring low input offset voltage, low input bias current, high input impedance, high slew rate and wide bandwidth. The devices also exhibit low noise and offset voltage drift.
Operational Amplifier, 2 Func, 20000uV Offset-Max, BIPolar, PDSO8
These devices are low cost, high speed, dual JFET input operational amplifiers with an internally trimmed input offset voltage (BI-FET II(TM) technology). They require low supply current yet maintain a large gain bandwidth product and fast slew rate. In addition, well matched high voltage JFET input devices provide very low input bias and offset currents. The TL082 is pin compatible with the standard LM1558 allowing designers to immediately upgrade the overall performance of existing LM1558 and most LM358 designs. These amplifiers may be used in applications such as high speed integrators, fast D/A converters, sample and hold circuits and many other circuits requiring low input offset voltage, low input bias current, high input impedance, high slew rate and wide bandwidth. The devices also exhibit low noise and offset voltage drift.
Popular Search Part Number
Related Keywords
Search Tags
Latest News
-
20 December 2023
What is the STM32F103C8T6 Microcontroller and How Does It Work?
Ⅰ. STM32F103C8T6 overviewⅡ. What are the features of STM32F103C8T6?Ⅲ. Programming of STM32F103C8T6Ⅳ. STM32F103C8T6 priceⅤ. What is the difference between STM32F103C8T6 and CH32F103C8T6?Ⅵ. Decoupling circuit of STM32F103C8T6Ⅶ. Several working... -
20 December 2023
1N4007 Diode Characteristics and Application Guide
Ⅰ. Introduction of 1N4007Ⅱ. Naming rules of 1N4007 diodeⅢ. Technical parameters of 1N4007 diodeⅣ. Can we use 1N4004 instead of 1N4007?Ⅴ. 1N4007 diode principle of operationⅥ. Electrical characteristic... -
21 December 2023
Comprehensive Exploration of BC547 Transistor: Advantages, Uses, Specifications and Working Status
Ⅰ. BC547 descriptionⅡ. What are the advantages of BC547 transistor?Ⅲ. BC547 application circuitⅣ. Specifications of BC547Ⅴ. Working status of BC547 transistorⅥ. Absolute maximum ratings of BC547Ⅶ. What are... -
21 December 2023
Exploring the PC817 Optocoupler: Working Principle, Package, Manufacturer and More
Ⅰ. What is PC817 optocoupler?Ⅱ. How PC817 optocoupler works?Ⅲ. Where can we use PC817 optocoupler?Ⅳ. PC817 optocoupler packageⅤ. How to measure the quality of PC817?Ⅵ. Manufacturer of PC817...
Help you to save your cost and time.
Reliable package for your goods.
Fast Reliable Delivery to save time.
Quality premium after-sale service.