Texas Instruments OPA2683IDRG4
- Part Number:
- OPA2683IDRG4
- Manufacturer:
- Texas Instruments
- Ventron No:
- 3696956-OPA2683IDRG4
- Description:
- IC OPAMP CFA 1.44GHZ 8SOIC
- Datasheet:
- OPA2683
Texas Instruments OPA2683IDRG4 technical specifications, attributes, parameters and parts with similar specifications to Texas Instruments OPA2683IDRG4.
- MountSurface Mount
- Mounting TypeSurface Mount
- Package / Case8-SOIC (0.154, 3.90mm Width)
- Number of Pins8
- Operating Temperature-40°C~85°C
- PackagingTape & Reel (TR)
- Pbfree Codeyes
- Part StatusObsolete
- Moisture Sensitivity Level (MSL)2 (1 Year)
- Number of Terminations8
- ECCN CodeEAR99
- SubcategoryOperational Amplifier
- TechnologyBIPOLAR
- Terminal PositionDUAL
- Terminal FormGULL WING
- Peak Reflow Temperature (Cel)NOT SPECIFIED
- Number of Functions2
- Time@Peak Reflow Temperature-Max (s)NOT SPECIFIED
- Base Part NumberOPA2683
- Pin Count8
- Qualification StatusNot Qualified
- Number of Circuits2
- Operating Supply Current1.88mA
- Nominal Supply Current2.06mA
- Slew Rate540V/μs
- Amplifier TypeCurrent Feedback
- Common Mode Rejection Ratio51 dB
- Current - Input Bias3μA
- Voltage - Supply, Single/Dual (±)5V~12V ±2.5V~6V
- Output Current per Channel150mA
- Input Offset Voltage (Vos)1.5mV
- Bandwidth145MHz
- Power Supply Rejection Ratio (PSRR)65dB
- 3db Bandwidth200MHz
- Length4.9mm
- Height Seated (Max)1.75mm
- RoHS StatusROHS3 Compliant
OPA2683IDRG4 Overview
It is packaged in an 8-SOIC (0.154, 3.90mm Width)-case that protects the operational amplifiers from damage. An op amp of this type is a Current Feedback-type. As far as the packaging is concerned, buffer op amp is delivered in a Tape & Reel (TR) case. It is estimated that there will be at least 8 terminations this year. A total of 8 pins are attached to buffer op amp. A type of Operational Amplifier op amp ic can be identified by the fact that this is a type of Operational Amplifier device. In total, the buffer amplifier consists of 8 pins. Op amp ic rates 1.5mV for input offset voltage. This electronic part is recommended for mounting type Surface Mount. In terms of operating temperature, this instrumentation amplifier is well suited to a temperature range of -40°C~85°C. A supply current of 1.88mA can be used to operate this linear amplifier. This op amp ic has 2 circuits.
OPA2683IDRG4 Features
8 Pins
OPA2683IDRG4 Applications
There are a lot of Texas Instruments
OPA2683IDRG4 Instrumentational OP Amps applications.
Logarithmic operation circuits
Exponential operation circuits
Multiplication circuits
Division circuits
Precision measurement
Power control
Information processing
Weak signal detection
Signal amplification
Signal filtering
It is packaged in an 8-SOIC (0.154, 3.90mm Width)-case that protects the operational amplifiers from damage. An op amp of this type is a Current Feedback-type. As far as the packaging is concerned, buffer op amp is delivered in a Tape & Reel (TR) case. It is estimated that there will be at least 8 terminations this year. A total of 8 pins are attached to buffer op amp. A type of Operational Amplifier op amp ic can be identified by the fact that this is a type of Operational Amplifier device. In total, the buffer amplifier consists of 8 pins. Op amp ic rates 1.5mV for input offset voltage. This electronic part is recommended for mounting type Surface Mount. In terms of operating temperature, this instrumentation amplifier is well suited to a temperature range of -40°C~85°C. A supply current of 1.88mA can be used to operate this linear amplifier. This op amp ic has 2 circuits.
OPA2683IDRG4 Features
8 Pins
OPA2683IDRG4 Applications
There are a lot of Texas Instruments
OPA2683IDRG4 Instrumentational OP Amps applications.
Logarithmic operation circuits
Exponential operation circuits
Multiplication circuits
Division circuits
Precision measurement
Power control
Information processing
Weak signal detection
Signal amplification
Signal filtering
OPA2683IDRG4 More Descriptions
ROHS3Compliant EAR99 OPA2683 Tape & Reel (TR) op amp buffer circuit 4.9mm 3muA 1.5mV 65dB
Operational Amplifier (Op-Amp) IC; No. of Amplifiers:2; Op Amp Type:Current Feedback; Gain Bandwidth -3db:200MHz; Slew Rate:210V/µs; Supply Voltage Min:5V; Supply Voltage Max:12V; No. of Pins:8 ;RoHS Compliant: Yes
The OPA2683 provides a new level of performance for dual, very low-power, wideband, current-feedback amplifiers. This CFBPLUS amplifier is among the first to use an internally closed-loop input buffer stage that significantly enhances performance over earlier low-power, current-feedback (CFB) amplifiers. This new architecture provides many of the advantages of a more ideal CFB amplifier while retaining the benefits of very low-power operation. The closed-loop input stage buffer gives a very low and linearized impedance path at the inverting input to sense the feedback error current. This improved inverting input impedance gives exceptional bandwidth retention to much higher gains and improved harmonic distortion over earlier solutions limited by inverting input linearity. Beyond simple high gain applications, the OPA2683 CFBPLUS amplifier can allow the gain setting element to be set with considerable freedom from amplifier bandwidth interaction. This flexibility allows frequency response peaking elements to be added, multiple input inverting summing circuits to have greater bandwidth, and low-power differential line drivers to meet the demanding requirements of DSL. The output capability for the OPA2683 also sets a new mark in performance for very low-power current-feedback amplifiers. Delivering a full 4Vpp swing on 5V supplies, the OPA2683 also has the output current to support this swing into a 100 load. This minimal output headroom requirement is complemented by a similar 1.2V input stage headroom giving exceptional capability for single 5V operation. The OPA2683s low 1.9mA total supply current is precisely trimmed at 25C. This trim, along with low shift over temperature and supply voltage, gives a very robust design over a wide range of operating conditions. Further system power reduction is possible using the shutdown feature of the MSOP-10 package.
Operational Amplifier (Op-Amp) IC; No. of Amplifiers:2; Op Amp Type:Current Feedback; Gain Bandwidth -3db:200MHz; Slew Rate:210V/µs; Supply Voltage Min:5V; Supply Voltage Max:12V; No. of Pins:8 ;RoHS Compliant: Yes
The OPA2683 provides a new level of performance for dual, very low-power, wideband, current-feedback amplifiers. This CFBPLUS amplifier is among the first to use an internally closed-loop input buffer stage that significantly enhances performance over earlier low-power, current-feedback (CFB) amplifiers. This new architecture provides many of the advantages of a more ideal CFB amplifier while retaining the benefits of very low-power operation. The closed-loop input stage buffer gives a very low and linearized impedance path at the inverting input to sense the feedback error current. This improved inverting input impedance gives exceptional bandwidth retention to much higher gains and improved harmonic distortion over earlier solutions limited by inverting input linearity. Beyond simple high gain applications, the OPA2683 CFBPLUS amplifier can allow the gain setting element to be set with considerable freedom from amplifier bandwidth interaction. This flexibility allows frequency response peaking elements to be added, multiple input inverting summing circuits to have greater bandwidth, and low-power differential line drivers to meet the demanding requirements of DSL. The output capability for the OPA2683 also sets a new mark in performance for very low-power current-feedback amplifiers. Delivering a full 4Vpp swing on 5V supplies, the OPA2683 also has the output current to support this swing into a 100 load. This minimal output headroom requirement is complemented by a similar 1.2V input stage headroom giving exceptional capability for single 5V operation. The OPA2683s low 1.9mA total supply current is precisely trimmed at 25C. This trim, along with low shift over temperature and supply voltage, gives a very robust design over a wide range of operating conditions. Further system power reduction is possible using the shutdown feature of the MSOP-10 package.
Popular Search Part Number
Related Keywords
Search Tags
Latest News
-
07 April 2024
BTS5030-1EJA Alternatives, Specification, Pinout, Features and Application
Ⅰ. BTS5030-1EJA overviewⅡ. BTS5030-1EJA specificationⅢ. Protection function of BTS5030-1EJAⅣ. Features of BTS5030-1EJAⅤ. How does BTS5030-1EJA realize real-time monitoring of the working status of the circuit?Ⅵ. BTS5030-1EJA pinout and... -
08 April 2024
CC2530F128RHAT Architecture, Replacements, Advantages, Applications and Other Details
Ⅰ. Overview of CC2530F128RHATⅡ. Concrete applications of CC2530F128RHATⅢ. Advantages of CC2530F128RHATⅣ. How to choose the energy-saving working mode for CC2530F128RHAT?Ⅴ. Technical parameters of CC2530F128RHATⅥ. Block diagram and architecture... -
08 April 2024
STM32F103RET6: Everything You Need to Know For Your Project
Ⅰ. Overview of STM32F103RET6Ⅱ. Importance of STM32F103RET6 in the field of technologyⅢ. Specifications of STM32F103RET6Ⅳ. The practical application of STM32F103RET6Ⅴ. Electrical characteristics of STM32F103RET6Ⅵ. How to use STM32F103RET6?Ⅶ.... -
09 April 2024
TPS82085SILR Characteristics, Specifications, Application Cases and More
Ⅰ. What is TPS82085SILR?Ⅱ. Characteristics of TPS82085SILRⅢ. Device functional modesⅣ. Specifications of TPS82085SILRⅤ. Thermal consideration of TPS82085SILRⅥ. What advanced technologies does TPS82085SILR use?Ⅶ. Competitive product analysis of TPS82085SILRⅧ....
Help you to save your cost and time.
Reliable package for your goods.
Fast Reliable Delivery to save time.
Quality premium after-sale service.