Texas Instruments LF411ACN
- Part Number:
- LF411ACN
- Manufacturer:
- Texas Instruments
- Ventron No:
- 3698488-LF411ACN
- Description:
- IC OPAMP JFET 4MHZ 8DIP
- Datasheet:
- LF411ACN
Texas Instruments LF411ACN technical specifications, attributes, parameters and parts with similar specifications to Texas Instruments LF411ACN.
- MountThrough Hole
- Mounting TypeThrough Hole
- Package / Case8-DIP (0.300, 7.62mm)
- Number of Pins8
- Operating Temperature0°C~70°C
- PackagingTube
- SeriesBI-FET II™
- JESD-609 Codee0
- Pbfree Codeno
- Part StatusObsolete
- Moisture Sensitivity Level (MSL)1 (Unlimited)
- Number of Terminations8
- ECCN CodeEAR99
- Terminal FinishTin/Lead (Sn/Pb)
- SubcategoryOperational Amplifier
- TechnologyBIPOLAR
- Terminal PositionDUAL
- Peak Reflow Temperature (Cel)NOT SPECIFIED
- Number of Functions1
- Supply Voltage15V
- Terminal Pitch2.54mm
- Reach Compliance Codenot_compliant
- Time@Peak Reflow Temperature-Max (s)NOT SPECIFIED
- Base Part NumberLF411
- Pin Count8
- Qualification StatusNot Qualified
- Operating Supply Voltage22V
- Number of Channels1
- Operating Supply Current1.8mA
- Nominal Supply Current1.8mA
- Power Dissipation670mW
- Output Current25mA
- Slew Rate15V/μs
- ArchitectureVOLTAGE-FEEDBACK
- Amplifier TypeJ-FET
- Common Mode Rejection Ratio80 dB
- Current - Input Bias50pA
- Voltage - Supply, Single/Dual (±)10V~44V ±5V~22V
- Input Offset Voltage (Vos)500μV
- Bandwidth3MHz
- Gain Bandwidth Product4MHz
- Neg Supply Voltage-Nom (Vsup)-15V
- Unity Gain BW-Nom4000 kHz
- Voltage Gain106.02dB
- Average Bias Current-Max (IIB)0.0002μA
- Power Supply Rejection Ratio (PSRR)80dB
- Low-OffsetYES
- Frequency CompensationYES
- Voltage - Input Offset300μV
- Low-BiasYES
- Bias Current-Max (IIB) @25C0.0002μA
- REACH SVHCNo SVHC
- RoHS StatusNon-RoHS Compliant
- Lead FreeContains Lead
LF411ACN Overview
In order to protect the op amps, a 8-DIP (0.300, 7.62mm) case is used. There are two types of operational amplifiers in this circuit. In the case of Tube cases, linear amplifier will be delivered. In recent months, the number of terminations has approached 8. It consists of a total of 8 pins in total. It would be helpful if you could remember that this op amp ic should be powered by an 15V battery. A type of Operational Amplifier buffer op amp is what this device is specifically, to be more precise. It has 8 pins that make up the linear amplifier. In terms of input offset voltage, operational amplifier rates 500μV. This electronic component is recommended to be mounted using the mounting type Through Hole. It is recommended that this op amp ic be operated at a temperature no higher than 0°C~70°C for optimal performance. In order for this instrumentation amplifier to operate, the supply current needs to be between 1.8mA and 10 . 106.02dB should remain the voltage gain. Buffer op amp is equipped with 1 channels on the device. The operating supply voltage of the buffer op amp is rated at 22V. BI-FET II™ is the number that corresponds to the series of the buffer op amp.
LF411ACN Features
8 Pins
supply voltage of 15V
106.02dB voltage gain
LF411ACN Applications
There are a lot of Texas Instruments
LF411ACN Instrumentational OP Amps applications.
Differentiator circuits
Logarithmic operation circuits
Exponential operation circuits
Multiplication circuits
Division circuits
Precision measurement
Power control
Information processing
Weak signal detection
Signal amplification
In order to protect the op amps, a 8-DIP (0.300, 7.62mm) case is used. There are two types of operational amplifiers in this circuit. In the case of Tube cases, linear amplifier will be delivered. In recent months, the number of terminations has approached 8. It consists of a total of 8 pins in total. It would be helpful if you could remember that this op amp ic should be powered by an 15V battery. A type of Operational Amplifier buffer op amp is what this device is specifically, to be more precise. It has 8 pins that make up the linear amplifier. In terms of input offset voltage, operational amplifier rates 500μV. This electronic component is recommended to be mounted using the mounting type Through Hole. It is recommended that this op amp ic be operated at a temperature no higher than 0°C~70°C for optimal performance. In order for this instrumentation amplifier to operate, the supply current needs to be between 1.8mA and 10 . 106.02dB should remain the voltage gain. Buffer op amp is equipped with 1 channels on the device. The operating supply voltage of the buffer op amp is rated at 22V. BI-FET II™ is the number that corresponds to the series of the buffer op amp.
LF411ACN Features
8 Pins
supply voltage of 15V
106.02dB voltage gain
LF411ACN Applications
There are a lot of Texas Instruments
LF411ACN Instrumentational OP Amps applications.
Differentiator circuits
Logarithmic operation circuits
Exponential operation circuits
Multiplication circuits
Division circuits
Precision measurement
Power control
Information processing
Weak signal detection
Signal amplification
LF411ACN More Descriptions
Operational Amplifier, Single, 3 Mhz, 1, 15 V/ S, 10V To 44V, Dip, 8 Rohs Compliant: Yes
Low Offset, Low Drift JFET Input Operational Amplifier 8-PDIP 0 to 70
Non-RoHS Compliant EAR99 LF411 Tin/Lead (Sn/Pb) op amp amplifier circuit 2.54mm 0.0002muA 500muV 4000kHz
OP Amp Single GP ±22V 8-Pin PDIP Rail
IC,LF411ACN,LOWOFFSET,LOWDRIFT JFET INPUT OP AMP,8 PIN DI
OP AMP, JFET LOW OFFSET, DIP8, 411
BI-FET LO-OFFSET OP-AMP (SING)
SSR RELAY SPST-NO 130MA 0-600V
Low Offset, Low Drift JFET Input Operational Amplifier 8-PDIP 0 to 70
Non-RoHS Compliant EAR99 LF411 Tin/Lead (Sn/Pb) op amp amplifier circuit 2.54mm 0.0002muA 500muV 4000kHz
OP Amp Single GP ±22V 8-Pin PDIP Rail
IC,LF411ACN,LOWOFFSET,LOWDRIFT JFET INPUT OP AMP,8 PIN DI
OP AMP, JFET LOW OFFSET, DIP8, 411
BI-FET LO-OFFSET OP-AMP (SING)
SSR RELAY SPST-NO 130MA 0-600V
Popular Search Part Number
Related Keywords
Search Tags
Latest News
-
21 December 2023
Exploring the PC817 Optocoupler: Working Principle, Package, Manufacturer and More
Ⅰ. What is PC817 optocoupler?Ⅱ. How PC817 optocoupler works?Ⅲ. Where can we use PC817 optocoupler?Ⅳ. PC817 optocoupler packageⅤ. How to measure the quality of PC817?Ⅵ. Manufacturer of PC817... -
22 December 2023
STM32F429IGT6 Microcontroller: Feature-Rich Embedded System Design
Ⅰ. What is STM32F429IGT6?Ⅱ. Application fields of STM32F429IGT6Ⅲ. Naming rules of STM32F429IGT6Ⅳ. Precautions for using STM32F429IGT6Ⅴ. STM32F429IGT6 characteristicsⅥ. Power supply diagram of STM32F429IGT6Ⅶ. Specifications of STM32F429IGT6Ⅷ. How to... -
22 December 2023
SS8050 NPN Epitaxial Silicon Transistor: Ideal for Small Power Amplification and Switching Applications
Ⅰ. Introduction of SS8050Ⅱ. Technical parameters of SS8050 transistorⅢ. NPN-type transistor and PNP-type transistorⅣ. How to use SS8050 transistor?Ⅴ. Electrical characteristics of SS8050 transistorⅥ. What is the difference... -
25 December 2023
N76E003AT20 Microcontroller: The Intelligent Engine of Embedded Systems
Ⅰ. What is N76E003AT20?Ⅱ. Characteristics of N76E003AT20 microcontrollerⅢ. N76E003AT20 dimension and packageⅣ. Operating modesⅤ. Who produces N76E003AT20 microcontroller?Ⅵ. N76E003AT20 microcontroller specificationsⅦ. What are the uses of N76E003AT20 microcontroller?Ⅷ....
Help you to save your cost and time.
Reliable package for your goods.
Fast Reliable Delivery to save time.
Quality premium after-sale service.