Texas Instruments INA129U/2K5G4
- Part Number:
- INA129U/2K5G4
- Manufacturer:
- Texas Instruments
- Ventron No:
- 3695446-INA129U/2K5G4
- Description:
- IC OPAMP INSTR 1.3MHZ 8SOIC
- Datasheet:
- INA129U/2K5G4
Texas Instruments INA129U/2K5G4 technical specifications, attributes, parameters and parts with similar specifications to Texas Instruments INA129U/2K5G4.
- Package / CaseSOIC
- Surface MountYES
- Number of Pins8
- Weight75.891673mg
- PackagingTape and Reel
- JESD-609 Codee4
- Moisture Sensitivity Level (MSL)3 (168 Hours)
- Number of Terminations8
- ECCN CodeEAR99
- Resistance100GOhm
- Terminal FinishNickel/Palladium/Gold (Ni/Pd/Au)
- Max Operating Temperature125°C
- Min Operating Temperature-40°C
- SubcategoryInstrumentation Amplifier
- TechnologyBIPOLAR
- Terminal PositionDUAL
- Terminal FormGULL WING
- Peak Reflow Temperature (Cel)260
- Number of Functions1
- Supply Voltage15V
- Pin Count8
- Number of Elements3
- Temperature GradeINDUSTRIAL
- Number of Channels1
- Max Supply Voltage36V
- Min Supply Voltage4.5V
- Nominal Supply Current750μA
- Quiescent Current700μA
- Slew Rate4 V/μs
- Amplifier TypeINSTRUMENTATION AMPLIFIER
- Common Mode Rejection Ratio120 dB
- Current - Input Bias5nA
- Input Offset Voltage (Vos)50μV
- Bandwidth1.3MHz
- Neg Supply Voltage-Nom (Vsup)-15V
- Voltage Gain80dB
- Average Bias Current-Max (IIB)0.005μA
- Max Dual Supply Voltage18V
- 3db Bandwidth1.3MHz
- Min Dual Supply Voltage2.25V
- Dual Supply Voltage15V
- Input Offset Current-Max (IIO)0.005μA
- Input Voltage Noise Density8nV/sqrt Hz
- Voltage Gain-Nom10
- Non-linearity-Max0.002%
- Length4.9mm
- Radiation HardeningNo
- RoHS StatusRoHS Compliant
- Lead FreeLead Free
INA129U/2K5G4 Overview
A SOIC case is used to package the op amp. INSTRUMENTATION AMPLIFIER-type instrumentation amplifiers are used in this application. The case in which buffer amplifier is delivered is called a Tape and Reel case. It is estimated that there will be 8 terminations in the next few months. There are a total of 8 pins on this op amp. It is important to remember that this op amp should be operated at a voltage of 15V volts. It should be noted that this op amp is a type of Instrumentation Amplifier device. There are 8 pins on this chip. In terms of the input offset voltage, instrumentation amplifier rates at 50μV. There should be no change in the voltage gain. There are 1 channels on the operational amplifiers. In order for op amp to function properly, the temperature should not be lower than -40°C degrees Celsius. Instrumentation amplifier should only be used at temperatures up to 125°C. There are a total of 3 elements in this linear amplifier. I would like to point out that this electrical component is capable of working from a voltage below 36V as far as the power supply is concerned. As a general rule, it is advisable to keep the op amp's supply voltage above 4.5V at all times. The dual supply voltage of 18V should be used for the conduct of this electronic component. There is a quiescent current of 700μA in this operational amplifier circuit. 100GOhm should be the range of resistance for the linear amplifier.
INA129U/2K5G4 Features
8 Pins
supply voltage of 15V
80dB voltage gain
Resistance of 100GOhm
INA129U/2K5G4 Applications
There are a lot of Texas Instruments
INA129U/2K5G4 Instrumentational OP Amps applications.
Addition operation circuits
Subtraction operation circuits
single/dual op amp sum and difference circuits
Integrator circuits
Differentiator circuits
Logarithmic operation circuits
Exponential operation circuits
Multiplication circuits
Division circuits
Precision measurement
A SOIC case is used to package the op amp. INSTRUMENTATION AMPLIFIER-type instrumentation amplifiers are used in this application. The case in which buffer amplifier is delivered is called a Tape and Reel case. It is estimated that there will be 8 terminations in the next few months. There are a total of 8 pins on this op amp. It is important to remember that this op amp should be operated at a voltage of 15V volts. It should be noted that this op amp is a type of Instrumentation Amplifier device. There are 8 pins on this chip. In terms of the input offset voltage, instrumentation amplifier rates at 50μV. There should be no change in the voltage gain. There are 1 channels on the operational amplifiers. In order for op amp to function properly, the temperature should not be lower than -40°C degrees Celsius. Instrumentation amplifier should only be used at temperatures up to 125°C. There are a total of 3 elements in this linear amplifier. I would like to point out that this electrical component is capable of working from a voltage below 36V as far as the power supply is concerned. As a general rule, it is advisable to keep the op amp's supply voltage above 4.5V at all times. The dual supply voltage of 18V should be used for the conduct of this electronic component. There is a quiescent current of 700μA in this operational amplifier circuit. 100GOhm should be the range of resistance for the linear amplifier.
INA129U/2K5G4 Features
8 Pins
supply voltage of 15V
80dB voltage gain
Resistance of 100GOhm
INA129U/2K5G4 Applications
There are a lot of Texas Instruments
INA129U/2K5G4 Instrumentational OP Amps applications.
Addition operation circuits
Subtraction operation circuits
single/dual op amp sum and difference circuits
Integrator circuits
Differentiator circuits
Logarithmic operation circuits
Exponential operation circuits
Multiplication circuits
Division circuits
Precision measurement
INA129U/2K5G4 More Descriptions
Instrumentation Amplifier, 1 Func, 550uV Offset-Max, 1.3MHz Band Width, BIPolar, PDSO8
Precision, Low Power Instrumentation Amplifiers 8-SOIC
SP Amp INSTR Amp Single ±18V 8-Pin SOIC T/R
Instrumentation Amplifier IC; Supply Voltage Min:4.5V; Supply Voltage Max:36V; Package/Case:8-SOIC; No. of Pins:8; Common Mode Ratio:120 dB; Leaded Process Compatible:Yes; Peak Reflow Compatible (260 C):Yes; Quiescent Current:0.7mA ;RoHS Compliant: Yes
Precision, Low Power Instrumentation Amplifiers 8-SOIC
SP Amp INSTR Amp Single ±18V 8-Pin SOIC T/R
Instrumentation Amplifier IC; Supply Voltage Min:4.5V; Supply Voltage Max:36V; Package/Case:8-SOIC; No. of Pins:8; Common Mode Ratio:120 dB; Leaded Process Compatible:Yes; Peak Reflow Compatible (260 C):Yes; Quiescent Current:0.7mA ;RoHS Compliant: Yes
Popular Search Part Number
Related Keywords
Search Tags
Latest News
-
30 November 2023
LM358 Dual Operational Amplifier Symbol, Features, LM393 vs LM358 and Applications
Ⅰ. Overview of LM358 operational amplifierⅡ. Features of LM358 operational amplifierⅢ. Symbol, footprint and pin configuration of LM358Ⅳ. Internal structure of LM358 chipⅤ. Working principle of LM358 operational... -
01 December 2023
LM2575 Adjustable Voltage Regulator Manufacturer, Layout Guidelines, Applications and Other Details
Ⅰ. What is LM2575?Ⅱ. Manufacturer of LM2575 voltage regulatorⅢ. What are the features of LM2575 voltage regulator?Ⅳ. The pin configuration of LM2575 voltage regulatorⅤ. How does the LM2575... -
01 December 2023
KA3525A PWM Controller Symbol, Equivalents, Working Principle and Applications
Ⅰ. What is PWM controller?Ⅱ. Overview of KA3525A PWM controllerⅢ. KA3525A symbol, footprint and pin configurationⅣ. Technical parameters of KA3525AⅤ. How does the KA3525A PWM controller work?Ⅵ. What... -
04 December 2023
TJA1043 CAN Transceiver: Features, Working Modes, Specifications and Applications
Ⅰ. Overview of TJA1043Ⅱ. What are the features of TJA1043 CAN transceiver?Ⅲ. Pin configuration of TJA1043 CAN transceiverⅣ. Working modes of TJA1043 CAN transceiverⅤ. How does the TJA1043...
Help you to save your cost and time.
Reliable package for your goods.
Fast Reliable Delivery to save time.
Quality premium after-sale service.