Texas Instruments BQ25616JRTWT
- Part Number:
- BQ25616JRTWT
- Manufacturer:
- Texas Instruments
- Ventron No:
- 6368961-BQ25616JRTWT
- Description:
- Standalone 1-cell 3.0-A buck battery charger with power path and 1.2-A boost operation
- Datasheet:
- bq25616
- Number of series cells1
- Charge current (max) (A)3
- Vin (max) (V)13.5
- Cell chemistryLi-Ion/Li-Polymer
- Battery charge voltage (min) (V)4.1
- Battery charge voltage (max) (V)4.35
- Absolute max Vin (max) (V)22
- Control topologySwitch-Mode Buck
- Control interfaceStandalone (RC-Settable)
- FeaturesBAT temp thermistor monitoring (hot/cold profile)
- Vin (min) (V)3.9
- RatingCatalog
- Operating temperature range (°C)-40 to 85
The BQ25616/616J is a highly integrated 3-A switch-mode battery charge management and system power path management device for single cell Li-Ion and Li-polymer batteries. The solution is highly integrated with input reverse-blocking FET (RBFET, Q1), high-side switching FET (HSFET, Q2), low-side switching FET (LSFET, Q3), and battery FET (BATFET, Q4) between system and battery. The low impedance power path optimizes switch-mode operation efficiency, reduces battery charging time and extends battery run time during discharging phase.
The BQ25616/616J is a highly integrated 3-A switch-mode battery charge management and system Power Path management device for Li-ion and Li-polymer batteries. It features fast charging with high input voltage support for a wide range of applications including speakers, industrial, and medical portable devices. Its low impedance power path optimizes switch-mode operation efficiency, reduces battery charging time, and extends battery run time during discharging phase. Its input voltage and current regulation deliver maximum charging power to the battery.
The solution is highly integrated with input reverse-blocking FET (RBFET, Q1), high-side switching FET (HSFET, Q2), low-side switching FET (LSFET, Q3), and battery FET (BATFET, Q4) between system and battery. It also integrates the bootstrap diode for the high-side gate drive for simplified system design. The hardware setting and status report provides easy configuration to set up the charging solution.
The device supports a wide range of input sources, including standard USB host port, USB charging port, USB compliant high voltage adapter and wireless power. It is compliant with USB 2.0 and USB 3.0 power spec with input current and voltage regulation. The device sets default input current limit based on the built-in USB detection through D /D- pins . When the device built-in USB interface identifies the input adaptor is unknown, the devices input current limit is determined by the ILIM pin setting resistor value.
The device integrates the buck charger and boost regulator into one solution with single inductor. It meets USB On-The-Go (OTG) operation power rating specification by supplying 5V with constant current limit up to 1.2-A.
The Power Path management regulates the system slightly above battery voltage but does not drop below 3.5-V minimum system voltage with adapter applied. With this feature, the system maintains operation even when the battery is completely depleted or removed. When the input current limit or voltage limit is reached, the Power Path management automatically reduces the charge current. As the system load continues to increase, the battery starts to discharge the battery until the system power requirement is met. This supplement mode prevents overloading the input source.
The device initiates and completes a charging cycle without software control. It senses the battery voltage and charges the battery in three phases: pre-conditioning, constant current and constant voltage. At the end of the charging cycle, the charger automatically terminates when the charge current is below a preset limit and the battery voltage is higher than the recharge threshold. If the fully charged battery falls below the recharge threshold, the charger automatically starts another charging cycle.
The charger provides various safety features for battery charging and system operations, including battery negative temperature coefficient thermistor monitoring, charging safety timer and overvoltage and over-current protections. Thermal regulation reduces charge current when the junction temperature exceeds 110°C. The STAT output reports the charging status and any fault conditions.
NO LEAD QUAD POWER SUPPLY SUPPORT CIRCUIT Active battery charger -40C~85C TA 0.5mm 3A 5V
Power Supply Support Circuit, Adjustable, 1 Channel, 3.9V, PQCC24
IC BATT CHG LI-ION 1CELL 24WQFN
Latest News
-
14 March 2024
What is the NE555 and How Does it Work?
Ⅰ. The birth background of NE555Ⅱ. Introduction to NE555Ⅲ. Design of NE555 timerⅣ. Internal composition of NE555Ⅴ. Operating modes of the NE555Ⅵ. Working principle of NE555Ⅶ. Application of... -
15 March 2024
ULN2003 Alternatives, Characteristics, Working Principle and Application
Ⅰ. ULN2003 overviewⅡ. What are the characteristics of ULN2003?Ⅲ. Pin diagram and functions of ULN2003Ⅳ. Working principle and function of ULN2003Ⅴ. ULN2003 drive circuit diagramⅥ. Where is ULN2003... -
15 March 2024
Detailed Explanation of 24C02 EEPROM Memory Chip
Ⅰ. Overview of 24C02Ⅱ. Functions of 24C02Ⅲ. Basic operations of 24C02Ⅳ. Application of 24C02Ⅴ. 24C02 pinoutⅥ. How to protect the data of 24C02?Ⅶ. How to use 24C02?EEPROM refers... -
18 March 2024
LM324N Internal Structure, Working Principle and LM324 vs LM324N
Ⅰ. Overview of LM324NⅡ. Internal structure and working principle of LM324NⅢ. Typical performance characteristics of LM324NⅣ. How to configure the power supply for LM324N?Ⅴ. Pin description of LM324NⅥ....
Help you to save your cost and time.
Reliable package for your goods.
Fast Reliable Delivery to save time.
Quality premium after-sale service.