Texas Instruments BQ25611DRTWT
- Part Number:
- BQ25611DRTWT
- Manufacturer:
- Texas Instruments
- Ventron No:
- 6368959-BQ25611DRTWT
- Description:
- I2C controlled 1-cell 3-A buck battery charger with USB detection and 1.2-A boost operation
- Datasheet:
- bq25611d
- Number of series cells1
- Charge current (max) (A)3
- Vin (max) (V)13.5
- Cell chemistryLi-Ion/Li-Polymer
- Battery charge voltage (min) (V)3.5
- Battery charge voltage (max) (V)4.52
- Absolute max Vin (max) (V)22
- Control topologySwitch-Mode Buck
- Control interfaceI2C
- FeaturesBAT temp thermistor monitoring (hot/cold profile)
- Vin (min) (V)3.9
- RatingCatalog
- Operating temperature range (°C)-40 to 85
The BQ25611D is a highly integrated 3-A switch-mode battery charge management and system power path management device for single cell Li-Ion and Li-polymer batteries. The solution is highly integrated with input reverse-blocking FET (RBFET, Q1), high-side switching FET (HSFET, Q2), low-side switching FET (LSFET, Q3), and battery FET (BATFET, Q4) between system and battery. The low impedance power path optimizes switch-mode operation efficiency, reduces battery charging time and extends battery run time during discharging phase.
The BQ25611D is a highly integrated 3-A switch-mode battery charge management and system Power Path management device for Li-ion and Li-polymer batteries. It features fast charging with high input voltage support for a wide range of applications including smart phones and tablets . Its low impedance power path optimizes switch-mode operation efficiency, reduces battery charging time, and extends battery run time during discharging phase. Its input voltage and current regulation and battery remote sensing deliver maximum charging power to the battery.
The solution is highly integrated with input reverse-blocking FET (RBFET, Q1), high-side switching FET (HSFET, Q2), low-side switching FET (LSFET, Q3), and battery FET (BATFET, Q4) between system and battery. It also integrates the bootstrap diode for the high-side gate drive for simplified system design. The I2C serial interface with charging and system settings makes the device a truly flexible solution.
The device supports a wide range of input sources, including standard USB host port, USB charging port, USB compliant high voltage adapter and wireless power. It is compliant with USB 2.0 and USB 3.0 power spec with input current and voltage regulation. The device takes the result from the detection circuit in the system, such as USB PHY device.
The device integrates the buck charger and boost regulator into one solution with single inductor. It meets USB On-The-Go (OTG) operation power rating specification by supplying 5 V (adjustable 4.6V / 4.75 V / 5 V / 5.15 V) with constant current limit up to 1.2 A.
The Power Path management regulates the system slightly above battery voltage but does not drop below 3.5-V minimum system voltage (programmable ) with adapter applied. With this feature, the system maintains operation even when the battery is completely depleted or removed. When the input current limit or voltage limit is reached, the Power Path management automatically reduces the charge current. As the system load continues to increase, the battery starts to discharge the battery until the system power requirement is met. This supplement mode prevents overloading the input source.
The device initiates and completes a charging cycle without software control. It senses the battery voltage and charges the battery in three phases: pre-conditioning, constant current and constant voltage. At the end of the charging cycle, the charger automatically terminates when the charge current is below a preset limit and the battery voltage is higher than the recharge threshold. If the fully charged battery falls below the recharge threshold, the charger automatically starts another charging cycle.
The charger provides various safety features for battery charging and system operations, including battery negative temperature coefficient thermistor monitoring, charging safety timer and overvoltage and over-current protections. Thermal regulation reduces charge current when the junction temperature exceeds 110°C. The status register reports the charging status and any fault conditions. With I2C, the VBUS_GD bit indicates if a good power source is present, and the INT output immediately notifies host when a fault occurs.
The device also provides the QON pin for BATFET enable and reset control to exit low power ship mode or full system reset function.
The BQ25611D device is available in 24-pin, 4 mm × 4 mm x 0.75 mm thin WQFN package.
I2C controlled 1-cell 3-A buck battery charger with USB detection and 1.2-A boost operation 24-WQFN -40 to 85
QUAD INDUSTRIAL POWER SUPPLY MANAGEMENT CIRCUIT Active battery charger 85C
IC BATT CHG LI-ION 1CELL 24WQFN
Latest News
-
30 October 2023
Car Audio Power Amplifier TDA7388: Equivalents, Features, TPA3116D2 vs TDA7388
Ⅰ. Overview of TDA7388 amplifierⅡ. TDA7388 symbol, footprint and pin configurationⅢ. Technical parameters of TDA7388 amplifierⅣ. What are the features of TDA7388 amplifier?Ⅴ. Differences between TPA3116D2 and TDA7388Ⅵ.... -
30 October 2023
TDA2822 Dual Power Amplifier: Pin Configuration, Applications and Additional Information
Ⅰ. Overview of TDA2822 amplifierⅡ. TDA2822 symbol, footprint and pin configurationⅢ. Technical parameters of TDA2822 amplifierⅣ. Features of TDA2822 amplifierⅤ. How does the TDA2822 amplifier work?Ⅵ. What are... -
31 October 2023
ESP32 vs RP2040 vs STM32: Which is Best for Your Project?
Ⅰ. What is a microcontroller?Ⅱ. ESP32 vs RP2040 vs STM32: OverviewⅢ. ESP32 vs RP2040 vs STM32: ManufacturersⅣ. ESP32 vs RP2040 vs STM32: Pin configurationⅤ. ESP32 vs RP2040 vs... -
31 October 2023
STM32F407VET6 Microcontroller: Symbol, Features, Working Principle
Ⅰ. What is STM32F407VET6 microcontroller?Ⅱ. Symbol, footprint and pin configuration of STM32F407VET6 microcontrollerⅢ. Technical parameters of STM32F407VET6 microcontrollerⅣ. Features of STM32F407VET6 microcontrollerⅤ. Dimension and package of STM32F407VET6 microcontrollerⅥ....
Help you to save your cost and time.
Reliable package for your goods.
Fast Reliable Delivery to save time.
Quality premium after-sale service.