Texas Instruments BQ25611DRTWR
- Part Number:
- BQ25611DRTWR
- Manufacturer:
- Texas Instruments
- Ventron No:
- 6368958-BQ25611DRTWR
- Description:
- I2C controlled 1-cell 3-A buck battery charger with USB detection and 1.2-A boost operation
- Datasheet:
- bq25611d
- Number of series cells1
- Charge current (max) (A)3
- Vin (max) (V)13.5
- Cell chemistryLi-Ion/Li-Polymer
- Battery charge voltage (min) (V)3.5
- Battery charge voltage (max) (V)4.52
- Absolute max Vin (max) (V)22
- Control topologySwitch-Mode Buck
- Control interfaceI2C
- FeaturesBAT temp thermistor monitoring (hot/cold profile)
- Vin (min) (V)3.9
- RatingCatalog
- Operating temperature range (°C)-40 to 85
The BQ25611D is a highly integrated 3-A switch-mode battery charge management and system power path management device for single cell Li-Ion and Li-polymer batteries. The solution is highly integrated with input reverse-blocking FET (RBFET, Q1), high-side switching FET (HSFET, Q2), low-side switching FET (LSFET, Q3), and battery FET (BATFET, Q4) between system and battery. The low impedance power path optimizes switch-mode operation efficiency, reduces battery charging time and extends battery run time during discharging phase.
The BQ25611D is a highly integrated 3-A switch-mode battery charge management and system Power Path management device for Li-ion and Li-polymer batteries. It features fast charging with high input voltage support for a wide range of applications including smart phones and tablets . Its low impedance power path optimizes switch-mode operation efficiency, reduces battery charging time, and extends battery run time during discharging phase. Its input voltage and current regulation and battery remote sensing deliver maximum charging power to the battery.
The solution is highly integrated with input reverse-blocking FET (RBFET, Q1), high-side switching FET (HSFET, Q2), low-side switching FET (LSFET, Q3), and battery FET (BATFET, Q4) between system and battery. It also integrates the bootstrap diode for the high-side gate drive for simplified system design. The I2C serial interface with charging and system settings makes the device a truly flexible solution.
The device supports a wide range of input sources, including standard USB host port, USB charging port, USB compliant high voltage adapter and wireless power. It is compliant with USB 2.0 and USB 3.0 power spec with input current and voltage regulation. The device takes the result from the detection circuit in the system, such as USB PHY device.
The device integrates the buck charger and boost regulator into one solution with single inductor. It meets USB On-The-Go (OTG) operation power rating specification by supplying 5 V (adjustable 4.6V / 4.75 V / 5 V / 5.15 V) with constant current limit up to 1.2 A.
The Power Path management regulates the system slightly above battery voltage but does not drop below 3.5-V minimum system voltage (programmable ) with adapter applied. With this feature, the system maintains operation even when the battery is completely depleted or removed. When the input current limit or voltage limit is reached, the Power Path management automatically reduces the charge current. As the system load continues to increase, the battery starts to discharge the battery until the system power requirement is met. This supplement mode prevents overloading the input source.
The device initiates and completes a charging cycle without software control. It senses the battery voltage and charges the battery in three phases: pre-conditioning, constant current and constant voltage. At the end of the charging cycle, the charger automatically terminates when the charge current is below a preset limit and the battery voltage is higher than the recharge threshold. If the fully charged battery falls below the recharge threshold, the charger automatically starts another charging cycle.
The charger provides various safety features for battery charging and system operations, including battery negative temperature coefficient thermistor monitoring, charging safety timer and overvoltage and over-current protections. Thermal regulation reduces charge current when the junction temperature exceeds 110°C. The status register reports the charging status and any fault conditions. With I2C, the VBUS_GD bit indicates if a good power source is present, and the INT output immediately notifies host when a fault occurs.
The device also provides the QON pin for BATFET enable and reset control to exit low power ship mode or full system reset function.
The BQ25611D device is available in 24-pin, 4 mm × 4 mm x 0.75 mm thin WQFN package.
I2C controlled 1-cell 3-A buck battery charger with USB detection and 1.2-A boost operation 24-WQFN -40 to 85
QUAD INDUSTRIAL POWER SUPPLY MANAGEMENT CIRCUIT Active (Battery Chemistry) IC Battery Charger 85C
IC BATT CHG LI-ION 1CELL 24WQFN
MOSFET 2N-CH 30V 9A/7.3A 8SOIC
Latest News
-
23 October 2023
A Basic Overview of SN74LS00N NAND Gates
Ⅰ. What are logic gates and NAND gates?Ⅱ. Overview of SN74LS00N NAND gatesⅢ. Symbol and footprint of SN74LS00N NAND gatesⅣ. Technical parameters of SN74LS00N NAND gatesⅤ. Features of... -
24 October 2023
2N5486 Transistor: Equivalent, Technical Parameters and Applications
Ⅰ. Overview of 2N5486 transistorⅡ. Symbol, footprint and pin configuration of 2N5486 transistorⅢ. Technical parameters of 2N5486 transistorⅣ. What are the features of 2N5486 transistor?Ⅴ. How to drive or use 2N5486... -
25 October 2023
UC3842AN Controller: Symbol, Features, Layout Guidelines and More Details
Ⅰ. What is UC3842AN controller?Ⅱ. Symbol, footprint and pin configuration of UC3842AN controllerⅢ. Technical parameters of UC3842AN controllerⅣ. Features of UC3842AN controllerⅤ. Layout guidelines for UC3842AN controllerⅥ. Absolute... -
25 October 2023
What Is MB10S Bridge Rectifier?
Ⅰ. What is a bridge rectifier?Ⅱ. Overview of MB10S bridge rectifierⅢ. Symbol, footprint and pin configuration of MB10S bridge rectifierⅣ. Technical parameters of MB10S bridge rectifierⅤ. Features of...
Help you to save your cost and time.
Reliable package for your goods.
Fast Reliable Delivery to save time.
Quality premium after-sale service.