Texas Instruments BQ25600CYFFR
- Part Number:
- BQ25600CYFFR
- Manufacturer:
- Texas Instruments
- Ventron No:
- 6368948-BQ25600CYFFR
- Description:
- I2C 1cell 3A Buck battery charger for Parallel Charging Applications
- Datasheet:
- bq25600c
- Number of series cells1
- Charge current (max) (A)3
- Vin (max) (V)13.5
- Cell chemistryLi-Ion/Li-Polymer
- Battery charge voltage (min) (V)3.856
- Battery charge voltage (max) (V)4.624
- Absolute max Vin (max) (V)22
- Control topologySwitch-Mode Buck
- Control interfaceI2C
- FeaturesIC thermal regulation
- Vin (min) (V)3.9
- RatingCatalog
- Operating temperature range (°C)-40 to 85
The bq25600C devices are highly-integrated 3.0-A switch-mode battery charge management and system power path management device for single cell Li-Ion and Li-polymer battery. The low impedance power path optimizes switch-mode operation efficiency and reduces battery charging time. The I2C serial interface with charging and system settings makes the device a truly flexible solution.
The bq25600C is highly-integrated 3.0-A switch-mode battery charge management and system power path management device for single cell Li-Ion and Li-polymer battery. It features fast charging with high input voltage and high efficiency, which supports parallel charge applications for a wide range of smart phones, tablets and portable devices. The bq25600C has different I2C address from bq25600 and thus only single I2C bus is needed when bq25600 is selected as a main charger and bq25600C is selected as a parallel charger. Its low impedance power path optimizes switch-mode operation efficiency, reduces battery charging time. Its input voltage and current regulation and battery remote sensing deliver maximum charging power to battery. The solution is highly integrated with input reverse-blocking FET (RBFET, Q1), high-side switching FET (HSFET, Q2), low-side switching FET (LSFET, Q3), and battery FET (BATFET, Q4) between system and battery. It also integrates the bootstrap diode for the high-side gate drive for simplified system design. The I2C serial interface with charging and system settings makes the device a truly flexible solution.
The device supports a wide range of input sources, including standard USB host port, USB charging port, and USB compliant high voltage adapter. The device sets default input current limit based on the built-in USB interface. To set the default input current limit, the device uses the built-in USB interface, or takes the result from detection circuit in the system, such as USB PHY device. The device is compliant with USB 2.0 and USB 3.0 power spec with input current and voltage regulation.
The device initiates and completes a charging cycle without software control. It senses the battery voltage and charges the battery in three phases: pre-conditioning, constant current and constant voltage. At the end of the charging cycle, the charger automatically terminates when the charge current is below a preset limit and the battery voltage is higher than recharge threshold. If the fully charged battery falls below the recharge threshold, the charger automatically starts another charging cycle.
The charger provides various safety features for battery charging and system operations, including charging safety timer and overvoltage and overcurrent protections. The thermal regulation reduces charge current when the junction temperature exceeds 110°C (programmable). The STAT output reports the charging status and any fault conditions. Other safety features include thermal regulation and thermal shutdown and input UVLO and overvoltage protection. The VBUS_GD bit indicates if a good power source is present. The INT output Immediately notifies host when fault occurs.
The devices are available in 30-ball, 2.0 mm × 2.4 mm WCSP package.
BQ25600C I2C Controlled 3A Single Cell Battery Charger 3.9V to 13.5V 30-Pin DSBGA T/R
Switching Battery Charger Li-Ion/Li-Pol 3000mA 3.856V to 4.624V 30-Pin DSBGA T/R
Latest News
-
03 November 2023
TCA9548APWR Symbol, Features, Layout Guidelines and TCA9548APWR vs PCA9548APW-T
Ⅰ. What is a multiplexer?Ⅱ. Overview of TCA9548APWRⅢ. TCA9548APWR symbol, footprint and pin configurationⅣ. What are the features of TCA9548APWR?Ⅴ. Technical parameters of TCA9548APWRⅥ. Layout guidelines for TCA9548APWRⅦ.... -
06 November 2023
LM393M Comparator: Equivalents, Features and Layout Guidelines
Ⅰ. Overview of LM393M comparatorⅡ. Symbol, footprint and pin configuration of LM393M comparatorⅢ. Features of LM393M comparatorⅣ. Technical parameters of LM393M comparatorⅤ. Layout guidelines for LM393M comparatorⅥ. Applications... -
06 November 2023
An Introduction to the LM339AN Quad Voltage Comparator
Ⅰ. What is a comparator?Ⅱ. Overview of LM339AN comparatorⅢ. LM339AN symbol, footprint and pin configurationⅣ. What are the features of LM339AN comparator?Ⅴ. Technical parameters of LM339AN comparatorⅥ. Applications... -
07 November 2023
TLP250 MOSFET IGBT Driver: Manufacturer, Footprint and Applications
Ⅰ. Overview of TLP250Ⅱ. Manufacturer of TLP250Ⅲ. TLP250 symbol, footprint and pin configurationⅣ. What are the features of TLP250?Ⅴ. Technical parameters of TLP250Ⅵ. How to use TLP250 isolated...
Help you to save your cost and time.
Reliable package for your goods.
Fast Reliable Delivery to save time.
Quality premium after-sale service.