Analog Devices Inc. ADM8693ARU-REEL
- Part Number:
- ADM8693ARU-REEL
- Manufacturer:
- Analog Devices Inc.
- Ventron No:
- 3749317-ADM8693ARU-REEL
- Description:
- IC SUPERVSR MPU 4.4V ADJ 16TSSOP
- Datasheet:
- ADM8690-95
Analog Devices Inc. ADM8693ARU-REEL technical specifications, attributes, parameters and parts with similar specifications to Analog Devices Inc. ADM8693ARU-REEL.
- MountSurface Mount
- Mounting TypeSurface Mount
- Package / Case16-TSSOP (0.173, 4.40mm Width)
- Number of Pins16
- Operating Temperature-40°C~85°C TA
- PackagingTape & Reel (TR)
- JESD-609 Codee0
- Part StatusObsolete
- Moisture Sensitivity Level (MSL)1 (Unlimited)
- Number of Terminations16
- ECCN CodeEAR99
- SubcategoryPower Management Circuits
- TechnologyCMOS
- Terminal PositionDUAL
- Terminal FormGULL WING
- Peak Reflow Temperature (Cel)240
- Number of Functions1
- Supply Voltage5V
- Terminal Pitch0.65mm
- Reach Compliance Codenot_compliant
- Time@Peak Reflow Temperature-Max (s)30
- Base Part NumberADM8693
- OutputPush-Pull, Push-Pull
- Pin Count16
- Qualification StatusNot Qualified
- Power Supplies5V
- Number of Channels2
- Max Supply Voltage5.5V
- Min Supply Voltage4.5V
- Nominal Supply Current200μA
- Power Dissipation600mW
- Adjustable ThresholdNO
- Watchdog TimerYes
- ResetActive High/Active Low
- Voltage - Threshold4.4V
- Number of Voltages Monitored1
- Reset Timeout35ms Minimum
- Supply Current-Max (Isup)0.2mA
- Min Reset Threshold Voltage4.25V
- Max Reset Threshold Voltage4.48V
- Length5mm
- Width4.4mm
- RoHS StatusNon-RoHS Compliant
ADM8693ARU-REEL Overview
As far as the mounting terminals of this voltage supervisor are concerned, it has 16 in total. Packaging is in the form of a Tape & Reel (TR). In this IC power you will find 1 functions for you to refer to. Depending on the power managment ic you are looking at, you can find a total of 2 channels. In this IC management you will find 16-TSSOP (0.173, 4.40mm Width) functions for you to refer to. There are many benefits that this IC power shares with other Battery Backup Circuit products as well. In order to ensure a good reflow performance, the package peak reflow temperature must be set at 240. A supply voltage of 5V is used to conduct the PMIC chip. A supply voltage of 1 is used to conduct the PMIC chip. Surface Mount is the one that mounts power management. There is a subcategory called Power Management Circuits for this power management. In total, the power management has 16 pins in it. This power management system has 16 pins. A voltage (Vsup) that doesn't fall below 4.5V as the minimum supply voltage (Vsup) should be applied to this IC power in order to ensure its proper operation. The supply voltage (Vsup) should not exceed 5.5V volts in this IC power. The recommended mounting type for IC management is Surface Mount. The supervisors should be set to the following temperature: -40°C~85°C TA. While this power management is operating, it will output Push-Pull, Push-Pull as the output voltage. To find similar IC managements from the manufacturer, you can always search by ADM8693. It requires 5V watts of power to operate this voltage supervisor.
ADM8693ARU-REEL Features
Battery Backup Circuit type
Minimum supply voltage of 4.5V
ADM8693ARU-REEL Applications
There are a lot of Analog Devices Inc.
ADM8693ARU-REEL Voltage Supervisors applications.
External alarm
Display equipment
DC stabilized power supply module
Insulation fault location system
Magnetic resonance imaging
Stable power system
Sensitive sensors
Efficient information transmission
Functional modules
Consumer electronics
As far as the mounting terminals of this voltage supervisor are concerned, it has 16 in total. Packaging is in the form of a Tape & Reel (TR). In this IC power you will find 1 functions for you to refer to. Depending on the power managment ic you are looking at, you can find a total of 2 channels. In this IC management you will find 16-TSSOP (0.173, 4.40mm Width) functions for you to refer to. There are many benefits that this IC power shares with other Battery Backup Circuit products as well. In order to ensure a good reflow performance, the package peak reflow temperature must be set at 240. A supply voltage of 5V is used to conduct the PMIC chip. A supply voltage of 1 is used to conduct the PMIC chip. Surface Mount is the one that mounts power management. There is a subcategory called Power Management Circuits for this power management. In total, the power management has 16 pins in it. This power management system has 16 pins. A voltage (Vsup) that doesn't fall below 4.5V as the minimum supply voltage (Vsup) should be applied to this IC power in order to ensure its proper operation. The supply voltage (Vsup) should not exceed 5.5V volts in this IC power. The recommended mounting type for IC management is Surface Mount. The supervisors should be set to the following temperature: -40°C~85°C TA. While this power management is operating, it will output Push-Pull, Push-Pull as the output voltage. To find similar IC managements from the manufacturer, you can always search by ADM8693. It requires 5V watts of power to operate this voltage supervisor.
ADM8693ARU-REEL Features
Battery Backup Circuit type
Minimum supply voltage of 4.5V
ADM8693ARU-REEL Applications
There are a lot of Analog Devices Inc.
ADM8693ARU-REEL Voltage Supervisors applications.
External alarm
Display equipment
DC stabilized power supply module
Insulation fault location system
Magnetic resonance imaging
Stable power system
Sensitive sensors
Efficient information transmission
Functional modules
Consumer electronics
ADM8693ARU-REEL More Descriptions
IC SUPERVISOR 1 CHANNEL 16TSSOP
IC SUPERVSR MPU 4.4V ADJ 16TSSOP
The ADM8690–ADM8695 family of supervisory circuits offers complete single chip solutions for power supply monitoring and battery control functions in microprocessor systems. These functions include mP reset, backup battery switchover, watchdog timer, CMOS RAM write protection and power failure warning. The complete family provides a variety of configurations to satisfy most microprocessor system requirements. The ADM8690, ADM8692 and ADM8694 are available in 8-pin DIP packages and provide: Power-on reset output during power-up, power-down and brownout conditions. The RESET output remains operational with VCC as low as 1 V. Battery backup switching for CMOS RAM, CMOS microprocessor or other low power logic. A reset pulse if the optional watchdog timer has not been toggled within a specified time. A 1.3 V threshold detector for power fail warning, low battery detection or to monitor a power supply other than 5 V. The ADM8691, ADM8693 and ADM8695 are available in 16-pin DIP and small outline packages (including TSSOP) and provide three additional functions: Write protection of CMOS RAM or EEPROM. Adjustable reset and watchdog timeout periods. Separate watchdog timeout, backup battery switchover, and low VCC status outputs.
IC SUPERVSR MPU 4.4V ADJ 16TSSOP
The ADM8690–ADM8695 family of supervisory circuits offers complete single chip solutions for power supply monitoring and battery control functions in microprocessor systems. These functions include mP reset, backup battery switchover, watchdog timer, CMOS RAM write protection and power failure warning. The complete family provides a variety of configurations to satisfy most microprocessor system requirements. The ADM8690, ADM8692 and ADM8694 are available in 8-pin DIP packages and provide: Power-on reset output during power-up, power-down and brownout conditions. The RESET output remains operational with VCC as low as 1 V. Battery backup switching for CMOS RAM, CMOS microprocessor or other low power logic. A reset pulse if the optional watchdog timer has not been toggled within a specified time. A 1.3 V threshold detector for power fail warning, low battery detection or to monitor a power supply other than 5 V. The ADM8691, ADM8693 and ADM8695 are available in 16-pin DIP and small outline packages (including TSSOP) and provide three additional functions: Write protection of CMOS RAM or EEPROM. Adjustable reset and watchdog timeout periods. Separate watchdog timeout, backup battery switchover, and low VCC status outputs.
The three parts on the right have similar specifications to ADM8693ARU-REEL.
-
ImagePart NumberManufacturerMountMounting TypePackage / CaseNumber of PinsOperating TemperaturePackagingJESD-609 CodePart StatusMoisture Sensitivity Level (MSL)Number of TerminationsECCN CodeSubcategoryTechnologyTerminal PositionTerminal FormPeak Reflow Temperature (Cel)Number of FunctionsSupply VoltageTerminal PitchReach Compliance CodeTime@Peak Reflow Temperature-Max (s)Base Part NumberOutputPin CountQualification StatusPower SuppliesNumber of ChannelsMax Supply VoltageMin Supply VoltageNominal Supply CurrentPower DissipationAdjustable ThresholdWatchdog TimerResetVoltage - ThresholdNumber of Voltages MonitoredReset TimeoutSupply Current-Max (Isup)Min Reset Threshold VoltageMax Reset Threshold VoltageLengthWidthRoHS StatusSurface MountPbfree CodeTerminal FinishJESD-30 CodeSupply Voltage-Max (Vsup)Additional FeatureOperating Temperature (Max)Operating Temperature (Min)Temperature GradeSupply Voltage-Min (Vsup)Height Seated (Max)View Compare
-
ADM8693ARU-REELSurface MountSurface Mount16-TSSOP (0.173, 4.40mm Width)16-40°C~85°C TATape & Reel (TR)e0Obsolete1 (Unlimited)16EAR99Power Management CircuitsCMOSDUALGULL WING24015V0.65mmnot_compliant30ADM8693Push-Pull, Push-Pull16Not Qualified5V25.5V4.5V200μA600mWNOYesActive High/Active Low4.4V135ms Minimum0.2mA4.25V4.48V5mm4.4mmNon-RoHS Compliant------------
-
-Surface MountTO-236-3, SC-59, SOT-23-3--40°C~150°C TATape & Reel (TR)e3Obsolete1 (Unlimited)3---DUALGULL WING26015V0.95mmunknown40-Push-Pull, Totem Pole3--1----NO-Active Low4.63V1140ms Minimum---2.9mm-ROHS3 CompliantYESyesMATTE TINR-PDSO-G35.5V------
-
-Surface Mount8-SOIC (0.154, 3.90mm Width)--Tape & Reel (TR)e0Obsolete1 (Unlimited)8--CMOSDUALGULL WING24015V--30-Push-Pull, Totem Pole8--3----NO-Active Low-1140ms Minimum---4.9mm3.9mmNon-RoHS CompliantYESnoTIN LEADR-PDSO-G85.5VRESET THRESHOLD VOLTAGE IS 4.65V85°C-40°CINDUSTRIAL1V-
-
-Through Hole8-DIP (0.300, 7.62mm)--40°C~85°C TATubee3Obsolete3 (168 Hours)8--CMOSDUAL-NOT APPLICABLE15V2.54mmunknownNOT APPLICABLE-Push-Pull, Totem Pole8--3----NO-Active Low4.4V1140ms Minimum---9.88mm7.62mmROHS3 CompliantNOyesMATTE TINR-PDIP-T85.5V----1V5.33mm
Popular Search Part Number
Related Keywords
Search Tags
Latest News
-
08 March 2024
A Complete Guide to the TP4056 Battery Charger Module
Ⅰ. What is TP4056?Ⅱ. Block diagram of TP4056Ⅲ. Main parameters of TP4056Ⅳ. Pins and functions of TP4056Ⅴ. TP4056 charging circuit diagram explanationⅥ. Battery charging process of TP4056Ⅶ. Application... -
08 March 2024
In-depth Analysis of SS34 Schottky Diode
Ⅰ. Overview of SS34Ⅱ. Purpose of SS34 diodeⅢ. Technical parameters of SS34 diodeⅣ. Advantages of SS34 diodesⅤ. Working principle of SS34 diodeⅥ. Typical characteristics of SS34 diodesⅦ. Case... -
11 March 2024
BTS50085-1TMA Specifications, Functions, Purpose and More
Ⅰ. What is BTS50085-1TMA?Ⅱ. Specifications of BTS50085-1TMAⅢ. What are the functions of BTS50085-1TMA?Ⅳ. Inverse load current operation of BTS50085-1TMAⅤ. Externally adjustable current limit of BTS50085-1TMAⅥ. How to use... -
11 March 2024
LM317: Ideal for Adjustable, High-Efficiency Three-Terminal Regulators
Ⅰ. Introduction to LM317Ⅱ. The function of LM317 adjustable voltage stabilized power supply voltage stabilizing circuitⅢ. Soft-start circuit of LM317Ⅳ. Minimum stable operating current of LM317Ⅴ. Calculation of...
Help you to save your cost and time.
Reliable package for your goods.
Fast Reliable Delivery to save time.
Quality premium after-sale service.