Analog Devices Inc. AD827JN
- Part Number:
- AD827JN
- Manufacturer:
- Analog Devices Inc.
- Ventron No:
- 3188006-AD827JN
- Description:
- IC OPAMP GP 50MHZ 8DIP
- Datasheet:
- AD827JN
Analog Devices Inc. AD827JN technical specifications, attributes, parameters and parts with similar specifications to Analog Devices Inc. AD827JN.
- Mounting TypeThrough Hole
- Package / Case8-DIP (0.300, 7.62mm)
- Surface MountNO
- Operating Temperature0°C~70°C
- PackagingTube
- JESD-609 Codee0
- Pbfree Codeno
- Part StatusObsolete
- Moisture Sensitivity Level (MSL)4 (72 Hours)
- Number of Terminations8
- Terminal FinishTIN LEAD
- SubcategoryOperational Amplifier
- Terminal PositionDUAL
- Peak Reflow Temperature (Cel)240
- Number of Functions2
- Supply Voltage15V
- Reach Compliance Codeunknown
- Time@Peak Reflow Temperature-Max (s)30
- Pin Count8
- JESD-30 CodeR-PDIP-T8
- Qualification StatusCOMMERCIAL
- Number of Circuits2
- Current - Supply10.5mA
- Slew Rate300V/μs
- Amplifier TypeGeneral Purpose
- Common Mode Rejection Ratio95 dB
- Current - Input Bias3.3μA
- Voltage - Supply, Single/Dual (±)±4.5V~18V
- Gain Bandwidth Product50MHz
- Neg Supply Voltage-Nom (Vsup)-15V
- Unity Gain BW-Nom50000 kHz
- Supply Voltage Limit-Max18V
- Voltage - Input Offset500μV
- Current - Output / Channel32mA
- Neg Supply Voltage-Max (Vsup)-18V
- Length9.88mm
- Height Seated (Max)5.33mm
- RoHS StatusNon-RoHS Compliant
AD827JN Overview
In the package, you will find a 8-DIP (0.300, 7.62mm)-case to contain the op amp ic. The instrumentation amplifier in this picture is of the General Purpose-type. A Tube case is used for delivering the op amp. During the past two weeks, there have been close to 8 terminations. A total of 8 pins are located on this board. This linear amplifier should be powered by an 15V battery. This particular linear amplifier is a type of Operational Amplifier device, to be precise. For this electrical component, Through Hole is the recommended mounting type. According to the manufacturer, this buffer op amp works well at 0°C~70°C , which is a good operating temperature. A instrumentation amplifier like this has 2 circuits. There is a recommendation that this electrical part be used with a supply with 10.5mA current rating.
AD827JN Features
8 Pins
supply voltage of 15V
AD827JN Applications
There are a lot of Rochester Electronics, LLC
AD827JN Instrumentational OP Amps applications.
Multiplication circuits
Division circuits
Precision measurement
Power control
Information processing
Weak signal detection
Signal amplification
Signal filtering
Signal operation
Video computer boards
In the package, you will find a 8-DIP (0.300, 7.62mm)-case to contain the op amp ic. The instrumentation amplifier in this picture is of the General Purpose-type. A Tube case is used for delivering the op amp. During the past two weeks, there have been close to 8 terminations. A total of 8 pins are located on this board. This linear amplifier should be powered by an 15V battery. This particular linear amplifier is a type of Operational Amplifier device, to be precise. For this electrical component, Through Hole is the recommended mounting type. According to the manufacturer, this buffer op amp works well at 0°C~70°C , which is a good operating temperature. A instrumentation amplifier like this has 2 circuits. There is a recommendation that this electrical part be used with a supply with 10.5mA current rating.
AD827JN Features
8 Pins
supply voltage of 15V
AD827JN Applications
There are a lot of Rochester Electronics, LLC
AD827JN Instrumentational OP Amps applications.
Multiplication circuits
Division circuits
Precision measurement
Power control
Information processing
Weak signal detection
Signal amplification
Signal filtering
Signal operation
Video computer boards
AD827JN More Descriptions
Operational Amplifier, 2 Func, 6000uV Offset-Max, PDIP8
STMICROELECTRONICS STBB3JR DC-DC Switching Buck-Boost Regulator, Adjustable, 1.8V-5.5Vin, 1.2V-5.5Vout, 2Aout, Flip Chip-20
The AD827 is a dual version of Analog Device's industry-standard AD847 op amp. Like the AD847, it provides high speed, low power performance at low cost. The AD827 achieves a 300 V/µs slew rate and 50 MHz unity-gain bandwidth while consuming only 100 mW when operating from ±5 volt power supplies. Performance is specified for operation using ±5 V to ±15 V power supplies. The AD827 offers an open-loop gain of 3,500 V/V into 500 Ohm loads. It also features a low input voltage noise of 15 nV/(root)Hz, and a low input offset voltage of 2 mV maximum. Common-mode rejection ratio is a minimum of 80 dB. Power supply rejection ratio is maintained at better than 20 dB with input frequencies as high as 1 MHz, thus minimizing noise feedthrough from switching power supplies. The AD827 is also ideal for use in demanding video applications, driving coaxial cables with less than 0.04% differential gain and 0.19° differential phase errors for 643 mV p-p into a 75 Ohm reverse terminated cable. The AD827 is also useful in multichannel, high speed data conversion systems where its fast (120 ns to 0.1%) settling time is of importance. In such applications, the AD827 serves as an input buffer for 8-bit to 10-bit A/D converters and as an output amplifier for high speed D/A converters.
STMICROELECTRONICS STBB3JR DC-DC Switching Buck-Boost Regulator, Adjustable, 1.8V-5.5Vin, 1.2V-5.5Vout, 2Aout, Flip Chip-20
The AD827 is a dual version of Analog Device's industry-standard AD847 op amp. Like the AD847, it provides high speed, low power performance at low cost. The AD827 achieves a 300 V/µs slew rate and 50 MHz unity-gain bandwidth while consuming only 100 mW when operating from ±5 volt power supplies. Performance is specified for operation using ±5 V to ±15 V power supplies. The AD827 offers an open-loop gain of 3,500 V/V into 500 Ohm loads. It also features a low input voltage noise of 15 nV/(root)Hz, and a low input offset voltage of 2 mV maximum. Common-mode rejection ratio is a minimum of 80 dB. Power supply rejection ratio is maintained at better than 20 dB with input frequencies as high as 1 MHz, thus minimizing noise feedthrough from switching power supplies. The AD827 is also ideal for use in demanding video applications, driving coaxial cables with less than 0.04% differential gain and 0.19° differential phase errors for 643 mV p-p into a 75 Ohm reverse terminated cable. The AD827 is also useful in multichannel, high speed data conversion systems where its fast (120 ns to 0.1%) settling time is of importance. In such applications, the AD827 serves as an input buffer for 8-bit to 10-bit A/D converters and as an output amplifier for high speed D/A converters.
The three parts on the right have similar specifications to AD827JN.
-
ImagePart NumberManufacturerMounting TypePackage / CaseSurface MountOperating TemperaturePackagingJESD-609 CodePbfree CodePart StatusMoisture Sensitivity Level (MSL)Number of TerminationsTerminal FinishSubcategoryTerminal PositionPeak Reflow Temperature (Cel)Number of FunctionsSupply VoltageReach Compliance CodeTime@Peak Reflow Temperature-Max (s)Pin CountJESD-30 CodeQualification StatusNumber of CircuitsCurrent - SupplySlew RateAmplifier TypeCommon Mode Rejection RatioCurrent - Input BiasVoltage - Supply, Single/Dual (±)Gain Bandwidth ProductNeg Supply Voltage-Nom (Vsup)Unity Gain BW-NomSupply Voltage Limit-MaxVoltage - Input OffsetCurrent - Output / ChannelNeg Supply Voltage-Max (Vsup)LengthHeight Seated (Max)RoHS StatusLifecycle StatusFactory Lead TimeContact PlatingNumber of PinsECCN CodePacking MethodMax Power DissipationTechnologyTerminal FormBase Part NumberOutput TypeNumber of ChannelsOperating Supply CurrentPower DissipationQuiescent CurrentSupply Current-MaxArchitectureOutput Current per ChannelInput Offset Voltage (Vos)Voltage GainAverage Bias Current-Max (IIB)Power Supply Rejection Ratio (PSRR)Low-OffsetFrequency CompensationSettling TimeLow-BiasMicropowerProgrammable PowerInput CapacitanceWidebandInput Voltage Noise DensityLead FreeMountSeriesResistanceReflow Temperature-Max (s)Operating Supply VoltageNumber of ElementsPower SuppliesNominal Supply CurrentHeightWidthBandwidthBias Current-Max (IIB) @25CDual Supply VoltageREACH SVHCRadiation HardeningView Compare
-
AD827JNThrough Hole8-DIP (0.300, 7.62mm)NO0°C~70°CTubee0noObsolete4 (72 Hours)8TIN LEADOperational AmplifierDUAL240215Vunknown308R-PDIP-T8COMMERCIAL210.5mA300V/μsGeneral Purpose95 dB3.3μA±4.5V~18V50MHz-15V50000 kHz18V500μV32mA-18V9.88mm5.33mmNon-RoHS Compliant------------------------------------------------
-
Surface Mount8-SOIC (0.154, 3.90mm Width)YES-40°C~85°CTape & Reel (TR)e3noActive1 (Unlimited)8-Operational AmplifierDUAL26015V-308-Not Qualified--3V/μsJ-FET80 dB2pA5V~36V ±2.5V~18V1.9MHz-5V1800 kHz-300μV--4.9mm-ROHS3 CompliantPRODUCTION (Last Updated: 4 weeks ago)14 WeeksTin8EAR99TAPE AND REEL1WBIPOLARGULL WINGAD820Rail-to-Rail1900μA1W900μA0.9mAVOLTAGE-FEEDBACK20mA1mV120dB0.0025μA80dBNOYES4.5 μsYESYESNO2.8pFNO25nV/sqrt HzContains Lead---------------
-
Surface Mount8-SOIC (0.154, 3.90mm Width)--40°C~125°CTubee3noActive1 (Unlimited)8-Operational AmplifierDUAL26015V--8-Not Qualified--0.5V/μsDifferential76 dB-4.5V~5.5V100 kHz---2mV--5mm-ROHS3 CompliantPRODUCTION (Last Updated: 1 week ago)8 WeeksTin8EAR99---GULL WINGAD8206--2mA-----2mV26.02dB-70dB---------Contains LeadSurface MountAutomotive400kOhm305V15V2mA1.5mm4mm-----
-
Surface Mount8-SOIC (0.154, 3.90mm Width)YES-40°C~85°CTubee0noObsolete1 (Unlimited)8-Operational AmplifierDUAL24015V-308----3V/μsJ-FET80 dB2pA5V~36V ±2.5V~18V1.8MHz-5V1900 kHz-400μV--5mm-Non-RoHS Compliant--Lead, Tin8EAR99-1WBIPOLARGULL WINGAD820Rail-to-Rail1900μA1W900μA-VOLTAGE-FEEDBACK20mA1mV120dB0.005μA80dBNOYES4.5 μsYESYESNO2.8pF-25nV/sqrt HzContains Lead----9V--900μA1.5mm4mm1.9MHz0.000025μA3VNo SVHCNo
Popular Search Part Number
Related Keywords
Search Tags
Latest News
-
08 March 2024
A Complete Guide to the TP4056 Battery Charger Module
Ⅰ. What is TP4056?Ⅱ. Block diagram of TP4056Ⅲ. Main parameters of TP4056Ⅳ. Pins and functions of TP4056Ⅴ. TP4056 charging circuit diagram explanationⅥ. Battery charging process of TP4056Ⅶ. Application... -
08 March 2024
In-depth Analysis of SS34 Schottky Diode
Ⅰ. Overview of SS34Ⅱ. Purpose of SS34 diodeⅢ. Technical parameters of SS34 diodeⅣ. Advantages of SS34 diodesⅤ. Working principle of SS34 diodeⅥ. Typical characteristics of SS34 diodesⅦ. Case... -
11 March 2024
BTS50085-1TMA Specifications, Functions, Purpose and More
Ⅰ. What is BTS50085-1TMA?Ⅱ. Specifications of BTS50085-1TMAⅢ. What are the functions of BTS50085-1TMA?Ⅳ. Inverse load current operation of BTS50085-1TMAⅤ. Externally adjustable current limit of BTS50085-1TMAⅥ. How to use... -
11 March 2024
LM317: Ideal for Adjustable, High-Efficiency Three-Terminal Regulators
Ⅰ. Introduction to LM317Ⅱ. The function of LM317 adjustable voltage stabilized power supply voltage stabilizing circuitⅢ. Soft-start circuit of LM317Ⅳ. Minimum stable operating current of LM317Ⅴ. Calculation of...
Help you to save your cost and time.
Reliable package for your goods.
Fast Reliable Delivery to save time.
Quality premium after-sale service.