Analog Devices Inc. AD602AR-REEL7
- Part Number:
- AD602AR-REEL7
- Manufacturer:
- Analog Devices Inc.
- Ventron No:
- 3832437-AD602AR-REEL7
- Description:
- IC OPAMP VGA 35MHZ 16SOIC
- Datasheet:
- AD602AR-REEL7
Analog Devices Inc. AD602AR-REEL7 technical specifications, attributes, parameters and parts with similar specifications to Analog Devices Inc. AD602AR-REEL7.
- Mounting TypeSurface Mount
- Package / Case16-SOIC (0.295, 7.50mm Width)
- Surface MountYES
- Operating Temperature-40°C~85°C
- PackagingTape & Reel (TR)
- SeriesX-AMP®
- JESD-609 Codee0
- Pbfree Codeno
- Part StatusObsolete
- Moisture Sensitivity Level (MSL)1 (Unlimited)
- Number of Terminations16
- Terminal FinishTIN LEAD
- Terminal PositionDUAL
- Terminal FormGULL WING
- Peak Reflow Temperature (Cel)240
- Number of Functions1
- Supply Voltage5V
- Reach Compliance Codeunknown
- Time@Peak Reflow Temperature-Max (s)30
- Pin Count16
- JESD-30 CodeR-PDSO-G16
- Supply Voltage-Min (Vsup)4.75V
- Number of Circuits2
- Analog IC - Other TypeANALOG CIRCUIT
- Current - Supply11mA
- Slew Rate275V/μs
- Amplifier TypeVariable Gain
- Current - Input Bias350nA
- Voltage - Supply, Single/Dual (±)±4.75V~5.25V
- Neg Supply Voltage-Nom (Vsup)-5V
- Current - Output / Channel50mA
- 3db Bandwidth35MHz
- Length10.3mm
- RoHS StatusNon-RoHS Compliant
AD602AR-REEL7 Overview
Op amp is packaged in 16-SOIC (0.295, 7.50mm Width) case. Op amps are Variable Gain types of amplifier on the chip. Instrumentation amplifier is delivered in a Tape & Reel (TR) case. The number of terminations approaches 16. Linear amplifier has a total of 16 pins. Please take in mind that op amp should be run at 5V. Surface Mount is the recommended mounting type of operational amplifiers. With regard to operating temperature, op amp ranges -40°C~85°C. There are 2 circuits on op amps. To run supply current of buffer amplifier under 11mA. X-AMP® corresponds to linear amplifier's series. The other types of analog IC are as follwed ANALOG CIRCUIT.
AD602AR-REEL7 Features
16 Pins
supply voltage of 5V
AD602AR-REEL7 Applications
There are a lot of Rochester Electronics, LLC
AD602AR-REEL7 Instrumentational OP Amps applications.
Proportional operation circuits
Inverse/same-phase proportional circuit
Addition operation circuits
Subtraction operation circuits
single/dual op amp sum and difference circuits
Integrator circuits
Differentiator circuits
Logarithmic operation circuits
Exponential operation circuits
Multiplication circuits
Op amp is packaged in 16-SOIC (0.295, 7.50mm Width) case. Op amps are Variable Gain types of amplifier on the chip. Instrumentation amplifier is delivered in a Tape & Reel (TR) case. The number of terminations approaches 16. Linear amplifier has a total of 16 pins. Please take in mind that op amp should be run at 5V. Surface Mount is the recommended mounting type of operational amplifiers. With regard to operating temperature, op amp ranges -40°C~85°C. There are 2 circuits on op amps. To run supply current of buffer amplifier under 11mA. X-AMP® corresponds to linear amplifier's series. The other types of analog IC are as follwed ANALOG CIRCUIT.
AD602AR-REEL7 Features
16 Pins
supply voltage of 5V
AD602AR-REEL7 Applications
There are a lot of Rochester Electronics, LLC
AD602AR-REEL7 Instrumentational OP Amps applications.
Proportional operation circuits
Inverse/same-phase proportional circuit
Addition operation circuits
Subtraction operation circuits
single/dual op amp sum and difference circuits
Integrator circuits
Differentiator circuits
Logarithmic operation circuits
Exponential operation circuits
Multiplication circuits
AD602AR-REEL7 More Descriptions
IC OPAMP VGA 35MHZ 16SOIC
IC VARIABLE GAIN 2 CIRC 16SOIC
SPECIALTY ANALOG CIRCUIT PDSO16
The AD600/AD602 dual channel, low noise, variable gain amplifiers are optimized for use in ultrasound imaging systems, but are applicable to any application requiring precise gain, low noise and distortion, and wide bandwidth. Each independent channel provides a gain of 0 dB to 40 dB in the AD600 and -10 dB to 30 dB in the AD602. The lower gain of the AD602 results in an improved signal-to-noise ratio (SNR) at the output. However, both products have the same 1.4 nV/vHz input noise spectral density. The decibel gain is directly proportional to the control voltage, accurately calibrated, and supply and temperature-stable. To achieve the difficult performance objectives, a proprietary circuit form, the X-AMP®, was developed. Each channel of the X-AMP comprises a variable attenuator of 0 dB to -42.14 dB followed by a high speed fixed gain amplifier. In this way, the amplifier never has to cope with large inputs, and can benefit from the use of negative feedback to precisely define the gain and dynamics. The attenuator is realized as a 7-stage R-2R ladder network having an input resistance of 100 W, laser trimmed to ±2%. The attenuation between tap points is 6.02 dB; the gain-control circuit provides continuous interpolation between these taps. The resulting control function is linear in dB. The gain-control interfaces are fully differential, providing an input resistance of ~15 M W and a scale factor of 32 dB/V (that is, 31.25 mV/dB) defined by an internal voltage reference. The response time of this interface is less than 1 µs. Each channel also has an independent gating facility that optionally blocks signal transmission and sets the dc output level to within a few millivolts of the output ground. The gating control input is TTL- and CMOS-compatible. The maximum gain of the AD600 is 41.07 dB, and the maximum gain of the AD602 is 31.07 dB; the -3 dB bandwidth of both models is nominally 35 MHz, essentially independent of the gain. The SNR for a 1 V rms output and a 1 MHz noise bandwidth is typically 76 dB for the AD600 and 86 dB for the AD602. The amplitude response is flat within ±0.5 dB from 100 kHz to 10 MHz; over this frequency range, the group delay varies by less than ±2 ns at all gain settings. Each amplifier channel can drive 100 W load impedances with low distortion. For example, the peak specified output is ±2.5 V minimum into a 500 W load, or ±1 V into a 100 W load. For a 200 W load in shunt with 5 pF, the total harmonic distortion for a ±1 V sinusoidal output at 10 MHz is typically -60 dBc. The AD600J/AD602J are specified for operation from 0°C to 70°C and are available in 16-lead PDIP (N) and 16-lead SOIC packages. The AD600A/AD602A are specified for operation from -40°C to 85°C and are available in 16-lead CERDIP (Q) and 16-lead SOIC packages. The AD600S/AD602S are specified for operation from -55°C to 125°C, are available in a 16-lead CERDIP (Q) package, and are MIL-STD-883 compliant. The AD600S/AD602S are also available under DESC SMD 5962-94572. AD600 - Gain Range: 0 dB to 40 dB AD602 - Gain Range: -10 dB to 30 dB
IC VARIABLE GAIN 2 CIRC 16SOIC
SPECIALTY ANALOG CIRCUIT PDSO16
The AD600/AD602 dual channel, low noise, variable gain amplifiers are optimized for use in ultrasound imaging systems, but are applicable to any application requiring precise gain, low noise and distortion, and wide bandwidth. Each independent channel provides a gain of 0 dB to 40 dB in the AD600 and -10 dB to 30 dB in the AD602. The lower gain of the AD602 results in an improved signal-to-noise ratio (SNR) at the output. However, both products have the same 1.4 nV/vHz input noise spectral density. The decibel gain is directly proportional to the control voltage, accurately calibrated, and supply and temperature-stable. To achieve the difficult performance objectives, a proprietary circuit form, the X-AMP®, was developed. Each channel of the X-AMP comprises a variable attenuator of 0 dB to -42.14 dB followed by a high speed fixed gain amplifier. In this way, the amplifier never has to cope with large inputs, and can benefit from the use of negative feedback to precisely define the gain and dynamics. The attenuator is realized as a 7-stage R-2R ladder network having an input resistance of 100 W, laser trimmed to ±2%. The attenuation between tap points is 6.02 dB; the gain-control circuit provides continuous interpolation between these taps. The resulting control function is linear in dB. The gain-control interfaces are fully differential, providing an input resistance of ~15 M W and a scale factor of 32 dB/V (that is, 31.25 mV/dB) defined by an internal voltage reference. The response time of this interface is less than 1 µs. Each channel also has an independent gating facility that optionally blocks signal transmission and sets the dc output level to within a few millivolts of the output ground. The gating control input is TTL- and CMOS-compatible. The maximum gain of the AD600 is 41.07 dB, and the maximum gain of the AD602 is 31.07 dB; the -3 dB bandwidth of both models is nominally 35 MHz, essentially independent of the gain. The SNR for a 1 V rms output and a 1 MHz noise bandwidth is typically 76 dB for the AD600 and 86 dB for the AD602. The amplitude response is flat within ±0.5 dB from 100 kHz to 10 MHz; over this frequency range, the group delay varies by less than ±2 ns at all gain settings. Each amplifier channel can drive 100 W load impedances with low distortion. For example, the peak specified output is ±2.5 V minimum into a 500 W load, or ±1 V into a 100 W load. For a 200 W load in shunt with 5 pF, the total harmonic distortion for a ±1 V sinusoidal output at 10 MHz is typically -60 dBc. The AD600J/AD602J are specified for operation from 0°C to 70°C and are available in 16-lead PDIP (N) and 16-lead SOIC packages. The AD600A/AD602A are specified for operation from -40°C to 85°C and are available in 16-lead CERDIP (Q) and 16-lead SOIC packages. The AD600S/AD602S are specified for operation from -55°C to 125°C, are available in a 16-lead CERDIP (Q) package, and are MIL-STD-883 compliant. The AD600S/AD602S are also available under DESC SMD 5962-94572. AD600 - Gain Range: 0 dB to 40 dB AD602 - Gain Range: -10 dB to 30 dB
Popular Search Part Number
Related Keywords
Search Tags
Latest News
-
08 January 2024
MC34063ADR2G Switching Regulator Working Principle, Specifications and Applications
Ⅰ. MC34063ADR2G descriptionⅡ. Technical parameters of MC34063ADR2GⅢ. How does MC34063ADR2G work?Ⅳ. MC34063ADR2G symbol, footprint and pin configurationⅤ. What are the advantages and disadvantages of MC34063ADR2G?Ⅵ. What are the... -
08 January 2024
2N7002 Transistor Replacements, Working Principle, Price and Other Details
Ⅰ. What is 2N7002?Ⅱ. Working principle of 2N7002Ⅲ. Pin configuration and functions of 2N7002Ⅳ. Where is 2N7002 used?Ⅴ. What is the price of the 2N7002?Ⅵ. What are the... -
09 January 2024
STM8S005K6T6C Microcontroller: Provides Powerful Processing Capabilities for Smart Applications
Ⅰ. Overview of STM8S005K6T6CⅡ. Technical specifications of STM8S005K6T6CⅢ. Structure and functions of STM8S005K6T6CⅣ. Application fields of STM8S005K6T6CⅤ. Package of STM8S005K6T6CⅥ. What are the technical points of STM8S005K6T6C?Ⅶ. What... -
09 January 2024
The Best Guide to MMA8452QR1 Accelerometer
Ⅰ. What is an accelerometer?Ⅱ. Introduction to MMA8452QR1Ⅲ. How does MMA8452QR1 work?Ⅳ. Symbol, footprint and pin configuration of MMA8452QR1Ⅴ. What are the advantages of MMA8452QR1?Ⅵ. What are the...
Help you to save your cost and time.
Reliable package for your goods.
Fast Reliable Delivery to save time.
Quality premium after-sale service.