Analog Devices Inc. AD600AR
- Part Number:
- AD600AR
- Manufacturer:
- Analog Devices Inc.
- Ventron No:
- 3696543-AD600AR
- Description:
- IC OPAMP VGA 35MHZ 16SOIC
- Datasheet:
- AD600AR
Analog Devices Inc. AD600AR technical specifications, attributes, parameters and parts with similar specifications to Analog Devices Inc. AD600AR.
- Contact PlatingLead, Tin
- MountSurface Mount
- Mounting TypeSurface Mount
- Package / Case16-SOIC (0.295, 7.50mm Width)
- Number of Pins16
- Weight665.986997mg
- Operating Temperature-40°C~85°C
- PackagingTube
- SeriesX-AMP®
- JESD-609 Codee0
- Pbfree Codeno
- Part StatusObsolete
- Moisture Sensitivity Level (MSL)1 (Unlimited)
- Number of Terminations16
- ECCN CodeEAR99
- Resistance105Ohm
- Terminal FinishTin/Lead (Sn85Pb15)
- SubcategoryOther Analog ICs
- TechnologyCMOS
- Terminal PositionDUAL
- Terminal FormGULL WING
- Peak Reflow Temperature (Cel)240
- Number of Functions1
- Supply Voltage5V
- Time@Peak Reflow Temperature-Max (s)30
- Base Part NumberAD600
- Pin Count16
- Number of Elements2
- Number of Circuits2
- Analog IC - Other TypeANALOG CIRCUIT
- Operating Supply Current11mA
- Power Dissipation600mW
- Slew Rate275V/μs
- Amplifier TypeVariable Gain
- Common Mode Rejection Ratio30 dB
- Current - Input Bias350nA
- Voltage - Supply, Single/Dual (±)±4.75V~5.25V
- Output Current per Channel50mA
- Gain Bandwidth Product35MHz
- Neg Supply Voltage-Nom (Vsup)-5V
- Voltage Gain41.07dB
- Dual Supply Voltage5V
- Length10.3mm
- Radiation HardeningNo
- RoHS StatusNon-RoHS Compliant
- Lead FreeContains Lead
AD600AR Overview
Packaging for the buffer amplifier is in the form of a 16-SOIC (0.295, 7.50mm Width) case. A Variable Gain-type buffer amplifier is shown here. There is a Tube case that is delivered with the instrumentation amplifiers. A total of 16 terminations have been reported in the past few weeks. Buffer amplifier has a total of 16 pins on it. I would like you to keep in mind that this buffer amplifier needs to be run at a voltage of 5V. In more specific terms, this linear amplifier can be categoriOther Analog ICsed as a Other Analog ICs-type device. An 16-pin op amp ic is included in the package. For this electrical component, the recommended mounting type is Surface Mount, which is the most common. The buffer amplifier functions well at -40°C~85°C as far as operating temperature is concerned. Using a supply current of 11mA , this buffer op amp will be able to operate. Keeping the voltage gain at 41.07dB is the best course of action. The buffer amp consists of 2 circuits in total. A total of 2 elements are present in this linear amplifier. The X-AMP® stands for the buffer op amp's serial number. It is recommended to keep the buffer amps resistance within the range of 105Ohm. An analog IC that is also used in this instrumentation amplifier is referred to as the ANALOG CIRCUIT type.
AD600AR Features
16 Pins
supply voltage of 5V
41.07dB voltage gain
Resistance of 105Ohm
AD600AR Applications
There are a lot of Analog Devices Inc.
AD600AR Instrumentational OP Amps applications.
single/dual op amp sum and difference circuits
Integrator circuits
Differentiator circuits
Logarithmic operation circuits
Exponential operation circuits
Multiplication circuits
Division circuits
Precision measurement
Power control
Information processing
Packaging for the buffer amplifier is in the form of a 16-SOIC (0.295, 7.50mm Width) case. A Variable Gain-type buffer amplifier is shown here. There is a Tube case that is delivered with the instrumentation amplifiers. A total of 16 terminations have been reported in the past few weeks. Buffer amplifier has a total of 16 pins on it. I would like you to keep in mind that this buffer amplifier needs to be run at a voltage of 5V. In more specific terms, this linear amplifier can be categoriOther Analog ICsed as a Other Analog ICs-type device. An 16-pin op amp ic is included in the package. For this electrical component, the recommended mounting type is Surface Mount, which is the most common. The buffer amplifier functions well at -40°C~85°C as far as operating temperature is concerned. Using a supply current of 11mA , this buffer op amp will be able to operate. Keeping the voltage gain at 41.07dB is the best course of action. The buffer amp consists of 2 circuits in total. A total of 2 elements are present in this linear amplifier. The X-AMP® stands for the buffer op amp's serial number. It is recommended to keep the buffer amps resistance within the range of 105Ohm. An analog IC that is also used in this instrumentation amplifier is referred to as the ANALOG CIRCUIT type.
AD600AR Features
16 Pins
supply voltage of 5V
41.07dB voltage gain
Resistance of 105Ohm
AD600AR Applications
There are a lot of Analog Devices Inc.
AD600AR Instrumentational OP Amps applications.
single/dual op amp sum and difference circuits
Integrator circuits
Differentiator circuits
Logarithmic operation circuits
Exponential operation circuits
Multiplication circuits
Division circuits
Precision measurement
Power control
Information processing
AD600AR More Descriptions
SP Amp Variable Gain Amp Dual ±5.25V 16-Pin SOIC W Tube
IC VARIABLE GAIN 2 CIRC 16SOIC
French Electronic Distributor since 1988
IC REG LIN POS ADJ 300MA 8TDFN
The AD600/AD602 dual channel, low noise, variable gain amplifiers are optimized for use in ultrasound imaging systems, but are applicable to any application requiring precise gain, low noise and distortion, and wide bandwidth. Each independent channel provides a gain of 0 dB to 40 dB in the AD600 and -10 dB to 30 dB in the AD602. The lower gain of the AD602 results in an improved signal-to-noise ratio (SNR) at the output. However, both products have the same 1.4 nV/vHz input noise spectral density. The decibel gain is directly proportional to the control voltage, accurately calibrated, and supply and temperature-stable. To achieve the difficult performance objectives, a proprietary circuit form, the X-AMP®, was developed. Each channel of the X-AMP comprises a variable attenuator of 0 dB to -42.14 dB followed by a high speed fixed gain amplifier. In this way, the amplifier never has to cope with large inputs, and can benefit from the use of negative feedback to precisely define the gain and dynamics. The attenuator is realized as a 7-stage R-2R ladder network having an input resistance of 100 W, laser trimmed to ±2%. The attenuation between tap points is 6.02 dB; the gain-control circuit provides continuous interpolation between these taps. The resulting control function is linear in dB. The gain-control interfaces are fully differential, providing an input resistance of ~15 M W and a scale factor of 32 dB/V (that is, 31.25 mV/dB) defined by an internal voltage reference. The response time of this interface is less than 1 µs. Each channel also has an independent gating facility that optionally blocks signal transmission and sets the dc output level to within a few millivolts of the output ground. The gating control input is TTL- and CMOS-compatible. The maximum gain of the AD600 is 41.07 dB, and the maximum gain of the AD602 is 31.07 dB; the -3 dB bandwidth of both models is nominally 35 MHz, essentially independent of the gain. The SNR for a 1 V rms output and a 1 MHz noise bandwidth is typically 76 dB for the AD600 and 86 dB for the AD602. The amplitude response is flat within ±0.5 dB from 100 kHz to 10 MHz; over this frequency range, the group delay varies by less than ±2 ns at all gain settings. Each amplifier channel can drive 100 W load impedances with low distortion. For example, the peak specified output is ±2.5 V minimum into a 500 W load, or ±1 V into a 100 W load. For a 200 W load in shunt with 5 pF, the total harmonic distortion for a ±1 V sinusoidal output at 10 MHz is typically -60 dBc. The AD600J/AD602J are specified for operation from 0°C to 70°C and are available in 16-lead PDIP (N) and 16-lead SOIC packages. The AD600A/AD602A are specified for operation from -40°C to 85°C and are available in 16-lead CERDIP (Q) and 16-lead SOIC packages. The AD600S/AD602S are specified for operation from -55°C to 125°C, are available in a 16-lead CERDIP (Q) package, and are MIL-STD-883 compliant. The AD600S/AD602S are also available under DESC SMD 5962-94572. AD600 - Gain Range: 0 dB to 40 dB AD602 - Gain Range: -10 dB to 30 dB
IC VARIABLE GAIN 2 CIRC 16SOIC
French Electronic Distributor since 1988
IC REG LIN POS ADJ 300MA 8TDFN
The AD600/AD602 dual channel, low noise, variable gain amplifiers are optimized for use in ultrasound imaging systems, but are applicable to any application requiring precise gain, low noise and distortion, and wide bandwidth. Each independent channel provides a gain of 0 dB to 40 dB in the AD600 and -10 dB to 30 dB in the AD602. The lower gain of the AD602 results in an improved signal-to-noise ratio (SNR) at the output. However, both products have the same 1.4 nV/vHz input noise spectral density. The decibel gain is directly proportional to the control voltage, accurately calibrated, and supply and temperature-stable. To achieve the difficult performance objectives, a proprietary circuit form, the X-AMP®, was developed. Each channel of the X-AMP comprises a variable attenuator of 0 dB to -42.14 dB followed by a high speed fixed gain amplifier. In this way, the amplifier never has to cope with large inputs, and can benefit from the use of negative feedback to precisely define the gain and dynamics. The attenuator is realized as a 7-stage R-2R ladder network having an input resistance of 100 W, laser trimmed to ±2%. The attenuation between tap points is 6.02 dB; the gain-control circuit provides continuous interpolation between these taps. The resulting control function is linear in dB. The gain-control interfaces are fully differential, providing an input resistance of ~15 M W and a scale factor of 32 dB/V (that is, 31.25 mV/dB) defined by an internal voltage reference. The response time of this interface is less than 1 µs. Each channel also has an independent gating facility that optionally blocks signal transmission and sets the dc output level to within a few millivolts of the output ground. The gating control input is TTL- and CMOS-compatible. The maximum gain of the AD600 is 41.07 dB, and the maximum gain of the AD602 is 31.07 dB; the -3 dB bandwidth of both models is nominally 35 MHz, essentially independent of the gain. The SNR for a 1 V rms output and a 1 MHz noise bandwidth is typically 76 dB for the AD600 and 86 dB for the AD602. The amplitude response is flat within ±0.5 dB from 100 kHz to 10 MHz; over this frequency range, the group delay varies by less than ±2 ns at all gain settings. Each amplifier channel can drive 100 W load impedances with low distortion. For example, the peak specified output is ±2.5 V minimum into a 500 W load, or ±1 V into a 100 W load. For a 200 W load in shunt with 5 pF, the total harmonic distortion for a ±1 V sinusoidal output at 10 MHz is typically -60 dBc. The AD600J/AD602J are specified for operation from 0°C to 70°C and are available in 16-lead PDIP (N) and 16-lead SOIC packages. The AD600A/AD602A are specified for operation from -40°C to 85°C and are available in 16-lead CERDIP (Q) and 16-lead SOIC packages. The AD600S/AD602S are specified for operation from -55°C to 125°C, are available in a 16-lead CERDIP (Q) package, and are MIL-STD-883 compliant. The AD600S/AD602S are also available under DESC SMD 5962-94572. AD600 - Gain Range: 0 dB to 40 dB AD602 - Gain Range: -10 dB to 30 dB
Popular Search Part Number
Related Keywords
Search Tags
Latest News
-
13 March 2024
74HC595: Efficient 8-Bit Shift Register Chip
Ⅰ. Overview of 74HC595Ⅱ. Pins and functions of 74HC595Ⅲ. Logic diagram of 74HC595Ⅳ. Application of 74HC595Ⅴ. Design of multi-digit LED display based on 74HC595Ⅵ. LED driver circuit design... -
14 March 2024
Comprehensive Understanding of the 78M05 Chip
Ⅰ. Development history of linear voltage regulatorsⅡ. Introduction to 78M05Ⅲ. Pin layout of 78M05Ⅳ. External components of 78M05Ⅴ. Technical key points of 78M05Ⅵ. Internal circuit diagram of 78M05Ⅶ.... -
14 March 2024
What is the NE555 and How Does it Work?
Ⅰ. The birth background of NE555Ⅱ. Introduction to NE555Ⅲ. Design of NE555 timerⅣ. Internal composition of NE555Ⅴ. Operating modes of the NE555Ⅵ. Working principle of NE555Ⅶ. Application of... -
15 March 2024
ULN2003 Alternatives, Characteristics, Working Principle and Application
Ⅰ. ULN2003 overviewⅡ. What are the characteristics of ULN2003?Ⅲ. Pin diagram and functions of ULN2003Ⅳ. Working principle and function of ULN2003Ⅴ. ULN2003 drive circuit diagramⅥ. Where is ULN2003...
Help you to save your cost and time.
Reliable package for your goods.
Fast Reliable Delivery to save time.
Quality premium after-sale service.