Vishay BC Components MAL201331339E3

Mounting Type refers to the method by which an electronic component is attached to a printed circuit board (PCB) or other surface. Common mounting types include: * Through-hole: Component leads are inserted into holes in the PCB and soldered on the other side. * Surface-mount: Component is placed on the surface of the PCB and soldered in place. * Press-fit: Component is pressed into place on the PCB without soldering. * Socket: Component is inserted into a socket on the PCB, allowing for easy replacement. The mounting type is determined by factors such as the component's size, shape, and power requirements.

Package / Case refers to the physical housing or enclosure that encapsulates an electronic component. It provides protection, facilitates handling, and enables electrical connections. The package type determines the component's size, shape, pin configuration, and mounting options. Common package types include DIP (dual in-line package), SOIC (small outline integrated circuit), and BGA (ball grid array). The package also influences the component's thermal and electrical performance.

Operating Temperature is the range of temperatures at which an electronic component can function properly. It is typically specified in degrees Celsius (°C) and indicates the minimum and maximum temperatures at which the component can operate without experiencing damage or degradation. Operating Temperature is an important parameter to consider when designing electronic circuits, as it ensures that the components will function reliably in the intended operating environment.

Tolerance in electronic components refers to the allowable deviation from the specified value. It indicates the range within which the actual value of the component can vary while still meeting the manufacturer's specifications. Tolerance is typically expressed as a percentage of the nominal value, such as ±5% or ±10%. A lower tolerance indicates a tighter range of acceptable values, resulting in more precise and consistent performance.

Moisture Sensitivity Level (MSL) is a measure of the susceptibility of a surface mount electronic component to moisture-induced damage during soldering. It is classified into six levels, from 1 (least sensitive) to 6 (most sensitive). MSL is determined by the materials used in the component's construction, including the solderability of its terminals and the presence of moisture-absorbing materials. Components with higher MSL ratings require more stringent handling and storage conditions to prevent moisture absorption and subsequent damage during soldering.

Lead spacing refers to the distance between the centers of two adjacent leads on an electronic component. It is typically measured in millimeters (mm) or inches (in). Lead spacing is an important parameter to consider when designing printed circuit boards (PCBs), as it determines the size and layout of the board. Proper lead spacing ensures that the component can be properly mounted and soldered onto the PCB, and that there is sufficient clearance between the leads to prevent short circuits.

Ripple current is the alternating current (AC) component of the current flowing through a capacitor. It is caused by the charging and discharging of the capacitor as the AC voltage applied to it changes. The ripple current can cause the capacitor to heat up and can also lead to premature failure. The maximum ripple current that a capacitor can handle is specified in its datasheet.

Polarization in electronic components refers to the orientation of the electric field within the component. It is a measure of the component's ability to store electrical energy. A polarized component has a positive and a negative terminal, and the electric field is oriented from the positive to the negative terminal. When a polarized component is connected to a voltage source, the electric field is established and the component stores electrical energy.

Impedance is a measure of the opposition to the flow of alternating current (AC) in an electrical circuit. It is a complex quantity that has both magnitude and phase. The magnitude of impedance is measured in ohms, and the phase is measured in degrees. Impedance is determined by the resistance, inductance, and capacitance of the circuit. Resistance is the opposition to the flow of current due to the material of the conductor. Inductance is the opposition to the flow of current due to the magnetic field created by the current. Capacitance is the opposition to the flow of current due to the storage of charge on the plates of a capacitor.

Height, in the context of electronic components, refers to the vertical dimension of the component. It is typically measured in millimeters (mm) or inches (in). Height is an important parameter to consider when designing and assembling electronic circuits, as it affects the overall size and form factor of the device. Components with a smaller height are often preferred for applications where space is limited, such as in portable devices or embedded systems.