Description
The Intersil ISL95711 is a digitally controlled potentiometer (XDCP) consisting of a resistor array, wiper switches, a control section, and nonvolatile memory. The wiper position is controlled by an I²C interface.
The potentiometer is implemented by a resistor array composed of 127 resistive elements and a wiper switching network. The wiper terminal can be connected to either end of the resistor array or at any one of the Tap Positions in between, providing 128 steps of resolution between RL and RH. The "position" of the wiper is determined by the value assigned to the volatile Wiper Register (WR). This register has an associated non-volatile Initial Value Register (IVR). The value stored in the IVR will be written into the WR at power-up, allowing wiper position recall after power interruption. The WR and the IVR can be directly written to and read from using standard I²C interface protocol.
Features
Non-Volatile Solid-State Potentiometer
I²C Serial Interface with Hardwire Slave Address Allows Up to Four Devices per bus
DCP Terminal Voltage, from V- to Vcc
128 Wiper Tap Points
Wiper position can be stored in nonvolatile memory and recalled on power-up.
127 Resistive Elements
Typical Rtotal tempco ±50ppm/°C
Ratiometric Tempco 4ppm/°C
End to end resistance range 20%
Low Power CMOS
Standby current, 1μA
Active current, 200μA max
Vcc 2.7V to 5.5V
V- -2.7V to -5.5V
High Reliability
Endurance, 200,000 data changes per bit
Register data retention, 50 years
RTOTAL Values 10kΩ, 50kΩ
Package 10 Ld MSOP- Pb-free plus anneal (RoHS compliant)
Applications
Industrial and automotive control
Parameter and bias adjustments
Amplifier bias and control
The Intersil ISL95711 is a digitally controlled potentiometer (XDCP) consisting of a resistor array, wiper switches, a control section, and nonvolatile memory. The wiper position is controlled by an I²C interface.
The potentiometer is implemented by a resistor array composed of 127 resistive elements and a wiper switching network. The wiper terminal can be connected to either end of the resistor array or at any one of the Tap Positions in between, providing 128 steps of resolution between RL and RH. The "position" of the wiper is determined by the value assigned to the volatile Wiper Register (WR). This register has an associated non-volatile Initial Value Register (IVR). The value stored in the IVR will be written into the WR at power-up, allowing wiper position recall after power interruption. The WR and the IVR can be directly written to and read from using standard I²C interface protocol.
Features
Non-Volatile Solid-State Potentiometer
I²C Serial Interface with Hardwire Slave Address Allows Up to Four Devices per bus
DCP Terminal Voltage, from V- to Vcc
128 Wiper Tap Points
Wiper position can be stored in nonvolatile memory and recalled on power-up.
127 Resistive Elements
Typical Rtotal tempco ±50ppm/°C
Ratiometric Tempco 4ppm/°C
End to end resistance range 20%
Low Power CMOS
Standby current, 1μA
Active current, 200μA max
Vcc 2.7V to 5.5V
V- -2.7V to -5.5V
High Reliability
Endurance, 200,000 data changes per bit
Register data retention, 50 years
RTOTAL Values 10kΩ, 50kΩ
Package 10 Ld MSOP- Pb-free plus anneal (RoHS compliant)
Applications
Industrial and automotive control
Parameter and bias adjustments
Amplifier bias and control
Intersil ISL95711WIU10Z-T technical specifications, attributes, parameters and parts with similar specifications to Intersil ISL95711WIU10Z-T.
- Contact PlatingTin
- MountSurface Mount
- Package / CaseMSOP
- Number of Pins10
- PackagingCut Tape
- Published2004
- Tolerance20%
- JESD-609 Codee3
- Part StatusActive
- Moisture Sensitivity Level (MSL)1
- Number of Terminations10
- ECCN CodeEAR99
- Temperature Coefficient50 ppm/°C
- Resistance10kOhm
- Number of Positions128
- Max Operating Temperature85°C
- Min Operating Temperature-40°C
- SubcategoryDigital Potentiometers
- TechnologyCMOS
- Terminal PositionDUAL
- Terminal FormGULL WING
- Peak Reflow Temperature (Cel)260
- Number of Functions1
- Supply Voltage5V
- Terminal Pitch0.5mm
- Frequency400kHz
- Reflow Temperature-Max (s)40
- Pin Count10
- Power Supplies3.3/5V
- Temperature GradeINDUSTRIAL
- InterfaceI2C
- Number of Circuits1
- Max Supply Voltage-5.5V
- Min Supply Voltage-2.7V
- Nominal Supply Current-100μA
- Memory TypeNon-Volatile
- Converter TypeDIGITAL POTENTIOMETER
- Total Resistance10000Ohm
- Resistor Terminal Voltage-Max5V
- Resistor Terminal Voltage-Min-5V
- Length3mm
- Width3mm
- Radiation HardeningNo
- RoHS StatusRoHS Compliant
- Lead FreeLead Free
Popular Search Part Number
Related Keywords
Search Tags
Latest News
-
21 March 2024
A Comprehensive Guide to AO3400 Field-Effect Transistor
Ⅰ. Introduction to AO3400Ⅱ. AO3400 technical parametersⅢ. AO3400 symbol, footprint and pin configurationⅣ. AO3400 principle of operationⅤ. What is the typical circuit application of AO3400?Ⅵ. Manufacturer of AO3400Ⅶ.... -
22 March 2024
FT232RL Alternatives, Structure, Package and FT232RL vs FT232BL
Ⅰ. Development history of FT232RLⅡ. What is FT232RL?Ⅲ. Structure of FT232RLⅣ. FT232RL block diagramⅤ. How does FT232RL work?Ⅵ. Typical applications of FT232RLⅦ. Package of FT232RLⅧ. What is the... -
22 March 2024
TDA7265 Characteristics, Technical Parameters, Pinout and Application
Ⅰ. TDA7265 overviewⅡ. Characteristics of TDA7265Ⅲ. The technical parameters of TDA7265Ⅳ. TDA7265 pin connectionⅤ. TDA7265 protection mechanismⅥ. The application of TDA7265Ⅶ. TDA7265 application circuitⅧ. What are the common... -
25 March 2024
IR2110 MOSFET Driver Functions, Features, Working Principle and IR2110 vs IR2113
Ⅰ. IR2110 descriptionⅡ. Main functions of IR2110Ⅲ. Functional block diagram of IR2110Ⅳ. Summary of featuresⅤ. Working principle of IR2110Ⅵ. Application of IR2110Ⅶ. What is the difference between IR2110...
Help you to save your cost and time.
Reliable package for your goods.
Fast Reliable Delivery to save time.
Quality premium after-sale service.