Description
The Intersil ISL95711 is a digitally controlled potentiometer (XDCP) consisting of a resistor array, wiper switches, a control section, and nonvolatile memory. The wiper position is controlled by an I²C interface.
The potentiometer is implemented by a resistor array composed of 127 resistive elements and a wiper switching network. The wiper terminal can be connected to either end of the resistor array or at any one of the Tap Positions in between, providing 128 steps of resolution between RL and RH. The "position" of the wiper is determined by the value assigned to the volatile Wiper Register (WR). This register has an associated non-volatile Initial Value Register (IVR). The value stored in the IVR will be written into the WR at power-up, allowing wiper position recall after power interruption. The WR and the IVR can be directly written to and read from using standard I²C interface protocol.
Features
Non-Volatile Solid-State Potentiometer
I²C Serial Interface with Hardwire Slave Address Allows Up to Four Devices per bus
DCP Terminal Voltage, from V- to Vcc
128 Wiper Tap Points
Wiper position can be stored in nonvolatile memory and recalled on power-up.
127 Resistive Elements
Typical Rtotal tempco ±50ppm/°C
Ratiometric Tempco 4ppm/°C
End to end resistance range 20%
Low Power CMOS
Standby current, 1μA
Active current, 200μA max
Vcc 2.7V to 5.5V
V- -2.7V to -5.5V
High Reliability
Endurance, 200,000 data changes per bit
Register data retention, 50 years
RTOTAL Values 10kΩ, 50kΩ
Package 10 Ld MSOP- Pb-free plus anneal (RoHS compliant)
Applications
Industrial and automotive control
Parameter and bias adjustments
Amplifier bias and control
The Intersil ISL95711 is a digitally controlled potentiometer (XDCP) consisting of a resistor array, wiper switches, a control section, and nonvolatile memory. The wiper position is controlled by an I²C interface.
The potentiometer is implemented by a resistor array composed of 127 resistive elements and a wiper switching network. The wiper terminal can be connected to either end of the resistor array or at any one of the Tap Positions in between, providing 128 steps of resolution between RL and RH. The "position" of the wiper is determined by the value assigned to the volatile Wiper Register (WR). This register has an associated non-volatile Initial Value Register (IVR). The value stored in the IVR will be written into the WR at power-up, allowing wiper position recall after power interruption. The WR and the IVR can be directly written to and read from using standard I²C interface protocol.
Features
Non-Volatile Solid-State Potentiometer
I²C Serial Interface with Hardwire Slave Address Allows Up to Four Devices per bus
DCP Terminal Voltage, from V- to Vcc
128 Wiper Tap Points
Wiper position can be stored in nonvolatile memory and recalled on power-up.
127 Resistive Elements
Typical Rtotal tempco ±50ppm/°C
Ratiometric Tempco 4ppm/°C
End to end resistance range 20%
Low Power CMOS
Standby current, 1μA
Active current, 200μA max
Vcc 2.7V to 5.5V
V- -2.7V to -5.5V
High Reliability
Endurance, 200,000 data changes per bit
Register data retention, 50 years
RTOTAL Values 10kΩ, 50kΩ
Package 10 Ld MSOP- Pb-free plus anneal (RoHS compliant)
Applications
Industrial and automotive control
Parameter and bias adjustments
Amplifier bias and control
Intersil ISL95711UIU10Z technical specifications, attributes, parameters and parts with similar specifications to Intersil ISL95711UIU10Z.
- Mounting TypeSurface Mount
- Package / Case10-TFSOP, 10-MSOP (0.118, 3.00mm Width)
- Surface MountYES
- Operating Temperature-40°C~85°C
- PackagingTube
- SeriesXDCP™
- Tolerance±20%
- FeatureSelectable Address
- Part StatusObsolete
- Moisture Sensitivity Level (MSL)1 (Unlimited)
- Number of Terminations10
- ECCN CodeEAR99
- Temperature Coefficient50 ppm/°C
- Resistance50kOhm
- Number of Positions128
- Additional FeatureNONVOLATILE MEMORY
- TechnologyCMOS
- Voltage - Supply±2.7V~5.5V
- Terminal PositionDUAL
- Terminal FormGULL WING
- Number of Functions1
- Supply Voltage5V
- Terminal Pitch0.5mm
- ConfigurationPotentiometer
- InterfaceI2C
- Number of Circuits1
- Memory TypeNon-Volatile
- TaperLinear
- Negative Supply Voltage-Nom-5V
- Number of Taps128
- Total Resistance50000Ohm
- Resistance - Wiper (Ω) (Typ)70
- Resistor Terminal Voltage-Max5.5V
- Temperature Coefficient (Typ)±50ppm/°C
- Resistor Terminal Voltage-Min-2.7V
- Length3mm
- Width3mm
- RoHS StatusROHS3 Compliant
Popular Search Part Number
Related Keywords
Search Tags
Latest News
-
03 April 2024
ADUM1201BRZ-RL7 Alternatives, Specifications, Application and More
Ⅰ. Overview of ADUM1201BRZ-RL7Ⅱ. Specifications of ADUM1201BRZ-RL7Ⅲ. Propagation delay-related parametersⅣ. Application of ADUM1201BRZ-RL7Ⅴ. How to evaluate the performance of ADUM1201BRZ-RL7?Ⅵ. Functional block diagram of ADUM1201BRZ-RL7Ⅶ. PCB layout of... -
03 April 2024
SG3525 PWM IC Characteristics, Internal Structure, Working Principle and SG3525 vs SG3524
Ⅰ. Description of SG3525Ⅱ. Characteristics of SG3525Ⅲ. Internal structure and working principle of SG3525Ⅳ. Representative block diagram of SG3525Ⅴ. Application circuit of SG3525Ⅵ. How to adjust the frequency... -
07 April 2024
ATMEGA16A-AU Microcontroller: Characteristics, Structure, Technical Parameters and Package
Ⅰ. ATMEGA16A-AU overviewⅡ. Characteristics of ATMEGA16A-AUⅢ. Structure and functions of ATMEGA16A-AUⅣ. Technical parameters of ATMEGA16A-AUⅤ. Power consumption management of ATMEGA16A-AUⅥ. Application of ATMEGA16A-AUⅦ. ATMEGA16A-AU packageⅧ. How to build... -
07 April 2024
BTS5030-1EJA Alternatives, Specification, Pinout, Features and Application
Ⅰ. BTS5030-1EJA overviewⅡ. BTS5030-1EJA specificationⅢ. Protection function of BTS5030-1EJAⅣ. Features of BTS5030-1EJAⅤ. How does BTS5030-1EJA realize real-time monitoring of the working status of the circuit?Ⅵ. BTS5030-1EJA pinout and...
Help you to save your cost and time.
Reliable package for your goods.
Fast Reliable Delivery to save time.
Quality premium after-sale service.