Texas Instruments INA152EA/250G4
- Part Number:
- INA152EA/250G4
- Manufacturer:
- Texas Instruments
- Ventron No:
- 3194330-INA152EA/250G4
- Description:
- IC OPAMP DIFF 800KHZ 8VSSOP
- Datasheet:
- INA152EA/250G4
Texas Instruments INA152EA/250G4 technical specifications, attributes, parameters and parts with similar specifications to Texas Instruments INA152EA/250G4.
- Package / CaseVSSOP
- Surface MountYES
- Number of Pins8
- Weight25.996513mg
- PackagingTape and Reel
- JESD-609 Codee4
- Moisture Sensitivity Level (MSL)3 (168 Hours)
- Number of Terminations8
- ECCN CodeEAR99
- Resistance80kOhm
- Terminal FinishNickel/Palladium/Gold (Ni/Pd/Au)
- Max Operating Temperature85°C
- Min Operating Temperature-40°C
- SubcategoryOperational Amplifier
- TechnologyCMOS
- Terminal PositionDUAL
- Terminal FormGULL WING
- Peak Reflow Temperature (Cel)260
- Number of Functions1
- Supply Voltage10V
- Terminal Pitch0.65mm
- Pin Count8
- Temperature GradeINDUSTRIAL
- Number of Channels2
- Number of Circuits1
- Max Supply Voltage20V
- Min Supply Voltage2.7V
- Nominal Supply Current500μA
- Quiescent Current500μA
- Slew Rate0.4 V/μs
- Amplifier TypeOPERATIONAL AMPLIFIER
- Common Mode Rejection Ratio80 dB
- Input Offset Voltage (Vos)1.5mV
- Bandwidth800 kHz
- Gain Bandwidth Product800 kHz
- Neg Supply Voltage-Nom (Vsup)-10V
- Voltage Gain0dB
- Max Dual Supply Voltage10V
- Min Dual Supply Voltage1.35V
- Dual Supply Voltage9V
- Height970μm
- Length3mm
- Width3mm
- Radiation HardeningNo
- RoHS StatusRoHS Compliant
- Lead FreeLead Free
INA152EA/250G4 Overview
In order to protect the op amps, a VSSOP case is used. There are two types of operational amplifiers in this circuit. In the case of Tape and Reel cases, linear amplifier will be delivered. In recent months, the number of terminations has approached 8. It consists of a total of 8 pins in total. It would be helpful if you could remember that this op amp ic should be powered by an 10V battery. A type of Operational Amplifier buffer op amp is what this device is specifically, to be more precise. It has 8 pins that make up the linear amplifier. In terms of input offset voltage, operational amplifier rates 1.5mV. Maintain 0dB as the voltage gain. In total, there are 1 circuits on this buffer amplifier. Buffer op amp is equipped with 2 channels on the device. It is recommended that the temperature of this op amp ic should not fall below -40°C degrees Fahrenheit at any time. Linear amplifier shouldn't be used above 85°C degrees. When it comes to the voltage from which this electrical part will operate, it can operate at a maximum of less than 20V. It is recommended that you keep the instrumentation amplifier's supply voltage higher than 2.7V when using it. It is recommended that you conduct this electronic part using the dual supply voltage of 10V. There is an 500μA quiescent current in linear amplifier. It is important to keep the resistance within the 80kOhm range of the op amps.
INA152EA/250G4 Features
8 Pins
supply voltage of 10V
0dB voltage gain
Resistance of 80kOhm
INA152EA/250G4 Applications
There are a lot of Texas Instruments
INA152EA/250G4 Instrumentational OP Amps applications.
Differentiator circuits
Logarithmic operation circuits
Exponential operation circuits
Multiplication circuits
Division circuits
Precision measurement
Power control
Information processing
Weak signal detection
Signal amplification
In order to protect the op amps, a VSSOP case is used. There are two types of operational amplifiers in this circuit. In the case of Tape and Reel cases, linear amplifier will be delivered. In recent months, the number of terminations has approached 8. It consists of a total of 8 pins in total. It would be helpful if you could remember that this op amp ic should be powered by an 10V battery. A type of Operational Amplifier buffer op amp is what this device is specifically, to be more precise. It has 8 pins that make up the linear amplifier. In terms of input offset voltage, operational amplifier rates 1.5mV. Maintain 0dB as the voltage gain. In total, there are 1 circuits on this buffer amplifier. Buffer op amp is equipped with 2 channels on the device. It is recommended that the temperature of this op amp ic should not fall below -40°C degrees Fahrenheit at any time. Linear amplifier shouldn't be used above 85°C degrees. When it comes to the voltage from which this electrical part will operate, it can operate at a maximum of less than 20V. It is recommended that you keep the instrumentation amplifier's supply voltage higher than 2.7V when using it. It is recommended that you conduct this electronic part using the dual supply voltage of 10V. There is an 500μA quiescent current in linear amplifier. It is important to keep the resistance within the 80kOhm range of the op amps.
INA152EA/250G4 Features
8 Pins
supply voltage of 10V
0dB voltage gain
Resistance of 80kOhm
INA152EA/250G4 Applications
There are a lot of Texas Instruments
INA152EA/250G4 Instrumentational OP Amps applications.
Differentiator circuits
Logarithmic operation circuits
Exponential operation circuits
Multiplication circuits
Division circuits
Precision measurement
Power control
Information processing
Weak signal detection
Signal amplification
INA152EA/250G4 More Descriptions
TEXAS INSTRUMENTS - INA152EA/250G4 - DIFFERENTIAL AMPLIFIER, 800kHZ, 0.4V/uS, MSOP-8, FULL REEL
Single-Supply Difference Amplifier 8-VSSOP -40 to 85
Operational Amplifier, 1 Func, 1500uV Offset-Max, CMOS, PDSO8
SP Amp DIFF AMP Single R-R O/P ±10V/20V 8-Pin VSSOP T/R
Instrumentation Amplifier IC; Gain Max, V/V:1; Supply Voltage Min:2.7V; Supply Voltage Max:20V; Package/Case:8-VSSOP; No. of Pins:8; Operating Temperature Range:-40°C to 85°C; Common Mode Ratio:80 dB ;RoHS Compliant: Yes
Single-Supply Difference Amplifier 8-VSSOP -40 to 85
Operational Amplifier, 1 Func, 1500uV Offset-Max, CMOS, PDSO8
SP Amp DIFF AMP Single R-R O/P ±10V/20V 8-Pin VSSOP T/R
Instrumentation Amplifier IC; Gain Max, V/V:1; Supply Voltage Min:2.7V; Supply Voltage Max:20V; Package/Case:8-VSSOP; No. of Pins:8; Operating Temperature Range:-40°C to 85°C; Common Mode Ratio:80 dB ;RoHS Compliant: Yes
Popular Search Part Number
Related Keywords
Search Tags
Latest News
-
02 November 2023
MPX2010DP Pressure Sensor: Manufacturer, Pin Configuration, and Applications
Ⅰ. What is a pressure sensor?Ⅱ. Overview of MPX2010DP pressure sensorⅢ. Manufacturer of MPX2010DP pressure sensorⅣ. MPX2010DP symbol, footprint and pin configurationⅤ. Features of MPX2010DP pressure sensorⅥ. Technical... -
02 November 2023
S8050 Bipolar Transistor: Manufacturer, Specifications, S8050 vs SS8050 and More Details
Ⅰ. Introduction to S8050 transistorⅡ. Manufacturer of S8050 transistorⅢ. Specifications of S8050 transistorⅣ. Symbol, footprint and pin configuration of S8050 transistorⅤ. What are the features of S8050 transistor?Ⅵ.... -
03 November 2023
ULN2003AD Equivalents, Symbol, Working Principle and Layout Guidelines
Ⅰ. Overview of ULN2003ADⅡ. Symbol, footprint and pin configuration of ULN2003ADⅢ. Features of ULN2003ADⅣ. Technical parameters of ULN2003ADⅤ. Working principle of ULN2003ADⅥ. Layout guidelines for ULN2003ADⅦ. What are... -
03 November 2023
TCA9548APWR Symbol, Features, Layout Guidelines and TCA9548APWR vs PCA9548APW-T
Ⅰ. What is a multiplexer?Ⅱ. Overview of TCA9548APWRⅢ. TCA9548APWR symbol, footprint and pin configurationⅣ. What are the features of TCA9548APWR?Ⅴ. Technical parameters of TCA9548APWRⅥ. Layout guidelines for TCA9548APWRⅦ....
Help you to save your cost and time.
Reliable package for your goods.
Fast Reliable Delivery to save time.
Quality premium after-sale service.