Texas Instruments INA141UAE4
- Part Number:
- INA141UAE4
- Manufacturer:
- Texas Instruments
- Ventron No:
- 3195883-INA141UAE4
- Description:
- IC OPAMP INSTR 1MHZ 8SOIC
- ECAD Model:
-
- Datasheet:
- INA141UAE4
Texas Instruments INA141UAE4 technical specifications, attributes, parameters and parts with similar specifications to Texas Instruments INA141UAE4.
- Lifecycle StatusACTIVE (Last Updated: 1 week ago)
- Package / CaseSOIC
- Surface MountYES
- Number of Pins8
- Weight75.891673mg
- JESD-609 Codee4
- Pbfree Codeyes
- Moisture Sensitivity Level (MSL)3 (168 Hours)
- Number of Terminations8
- ECCN CodeEAR99
- Resistance10GOhm
- Terminal FinishNickel/Palladium/Gold (Ni/Pd/Au)
- Max Operating Temperature85°C
- Min Operating Temperature-40°C
- SubcategoryInstrumentation Amplifier
- Packing MethodTUBE
- TechnologyBIPOLAR
- Terminal PositionDUAL
- Terminal FormGULL WING
- Peak Reflow Temperature (Cel)260
- Number of Functions1
- Supply Voltage15V
- Pin Count8
- Number of Elements3
- Temperature GradeINDUSTRIAL
- Number of Circuits1
- Max Supply Voltage36V
- Min Supply Voltage4.5V
- Operating Supply Current750μA
- Quiescent Current750μA
- Slew Rate4 V/μs
- Amplifier TypeINSTRUMENTATION AMPLIFIER
- Common Mode Rejection Ratio110 dB
- Current - Input Bias10nA
- Output Current per Channel15mA
- Input Offset Voltage (Vos)125μV
- Bandwidth200 kHz
- Neg Supply Voltage-Nom (Vsup)-15V
- Average Bias Current-Max (IIB)0.005μA
- Max Dual Supply Voltage18V
- 3db Bandwidth1MHz
- Min Dual Supply Voltage2.25V
- Dual Supply Voltage15V
- Voltage Gain-Min10
- Input Voltage Noise Density8nV/sqrt Hz
- Voltage Gain-Nom10
- Non-linearity-Max0.002%
- Voltage Gain-Max100
- Height1.75mm
- Length4.9mm
- Width3.91mm
- Thickness1.58mm
- REACH SVHCNo SVHC
- Radiation HardeningNo
- RoHS StatusRoHS Compliant
- Lead FreeLead Free
INA141UAE4 Overview
In order to protect the op amps, a SOIC case is used. There are two types of operational amplifiers in this circuit. In recent months, the number of terminations has approached 8. It consists of a total of 8 pins in total. It would be helpful if you could remember that this op amp ic should be powered by an 15V battery. A type of Instrumentation Amplifier buffer op amp is what this device is specifically, to be more precise. It has 8 pins that make up the linear amplifier. In terms of input offset voltage, operational amplifier rates 125μV. In order for this instrumentation amplifier to operate, the supply current needs to be between 750μA and 10 . In total, there are 1 circuits on this buffer amplifier. It is recommended that the temperature of this op amp ic should not fall below -40°C degrees Fahrenheit at any time. Linear amplifier shouldn't be used above 85°C degrees. As a whole, there are 3 elements that make up this buffer amplifier. As a result of this, the buffer amplifier is packed in TUBE. When it comes to the voltage from which this electrical part will operate, it can operate at a maximum of less than 36V. It is recommended that you keep the instrumentation amplifier's supply voltage higher than 4.5V when using it. It is recommended that you conduct this electronic part using the dual supply voltage of 18V. There is an 750μA quiescent current in linear amplifier. A minimum voltage gain of 10 is the minimum voltage gain that this instrumentation amplifier is capable of producing. It is important to keep the resistance within the 10GOhm range of the op amps.
INA141UAE4 Features
8 Pins
supply voltage of 15V
Resistance of 10GOhm
INA141UAE4 Applications
There are a lot of Texas Instruments
INA141UAE4 Instrumentational OP Amps applications.
Differentiator circuits
Logarithmic operation circuits
Exponential operation circuits
Multiplication circuits
Division circuits
Precision measurement
Power control
Information processing
Weak signal detection
Signal amplification
In order to protect the op amps, a SOIC case is used. There are two types of operational amplifiers in this circuit. In recent months, the number of terminations has approached 8. It consists of a total of 8 pins in total. It would be helpful if you could remember that this op amp ic should be powered by an 15V battery. A type of Instrumentation Amplifier buffer op amp is what this device is specifically, to be more precise. It has 8 pins that make up the linear amplifier. In terms of input offset voltage, operational amplifier rates 125μV. In order for this instrumentation amplifier to operate, the supply current needs to be between 750μA and 10 . In total, there are 1 circuits on this buffer amplifier. It is recommended that the temperature of this op amp ic should not fall below -40°C degrees Fahrenheit at any time. Linear amplifier shouldn't be used above 85°C degrees. As a whole, there are 3 elements that make up this buffer amplifier. As a result of this, the buffer amplifier is packed in TUBE. When it comes to the voltage from which this electrical part will operate, it can operate at a maximum of less than 36V. It is recommended that you keep the instrumentation amplifier's supply voltage higher than 4.5V when using it. It is recommended that you conduct this electronic part using the dual supply voltage of 18V. There is an 750μA quiescent current in linear amplifier. A minimum voltage gain of 10 is the minimum voltage gain that this instrumentation amplifier is capable of producing. It is important to keep the resistance within the 10GOhm range of the op amps.
INA141UAE4 Features
8 Pins
supply voltage of 15V
Resistance of 10GOhm
INA141UAE4 Applications
There are a lot of Texas Instruments
INA141UAE4 Instrumentational OP Amps applications.
Differentiator circuits
Logarithmic operation circuits
Exponential operation circuits
Multiplication circuits
Division circuits
Precision measurement
Power control
Information processing
Weak signal detection
Signal amplification
INA141UAE4 More Descriptions
Precision, Low Power, G = 10, 100 Instrumentation Amplifier 8-SOIC -40 to 85
TEXAS INSTRUMENTS INA141UAE4 Instrument Amplifier, 1, 250 V, 4 V/s, 200 kHz,2.25V to18V, SOIC
Instrumentation Amplifier, 1 Func, 50uV Offset-Max, 1MHz Band Width, BIPolar, PDSO8
SP Amp INSTR Amp Single ±18V 8-Pin SOIC Tube
TEXAS INSTRUMENTS INA141UAE4 Instrument Amplifier, 1, 250 V, 4 V/s, 200 kHz,2.25V to18V, SOIC
Instrumentation Amplifier, 1 Func, 50uV Offset-Max, 1MHz Band Width, BIPolar, PDSO8
SP Amp INSTR Amp Single ±18V 8-Pin SOIC Tube
Popular Search Part Number
Related Keywords
Search Tags
Latest News
-
17 October 2023
IRFP250 Transistor Equivalent, Pin Configuration, Working Principle and More
Ⅰ. Overview of IRFP250Ⅱ. Symbol, footprint and pin configuration of IRFP250Ⅲ. Technical parameters of IRFP250Ⅳ. What are the features of IRFP250?Ⅴ. Working principle of IRFP250Ⅵ. Applications of IRFP250Ⅶ.... -
17 October 2023
A Review of TDA2009A Dual Audio Power Amplifier
Ⅰ. What is TDA2009A?Ⅱ. Symbol, footprint and pin configuration of TDA2009AⅢ. Technical parameters of TDA2009AⅣ. What are the features of TDA2009A?Ⅴ. How does the overheating protection circuit of... -
18 October 2023
What Is CD4017BE CMOS Counter And How It Works?
Ⅰ. Overview of CD4017BE counterⅡ. Symbol, footprint and pin configuration of CD4017BEⅢ. Technical parameters of CD4017BEⅣ. What are the features of CD4017BE?Ⅴ. How does CD4017BE work?Ⅵ. What are... -
18 October 2023
Get to Know the MOC3063 Triac Driver
Ⅰ. What is an optocoupler?Ⅱ. Overview of MOC3063 optocouplerⅢ. Symbol, footprint and pin configuration of MOC3063Ⅳ. Technical parameters of MOC3063Ⅴ. What are the features of MOC3063?Ⅵ. Working principle...
Help you to save your cost and time.
Reliable package for your goods.
Fast Reliable Delivery to save time.
Quality premium after-sale service.