Analog Devices Inc. AMP02EP
- Part Number:
- AMP02EP
- Manufacturer:
- Analog Devices Inc.
- Ventron No:
- 3696568-AMP02EP
- Description:
- IC OPAMP INSTR 1.2MHZ 8DIP
- Datasheet:
- AMP02EP
Analog Devices Inc. AMP02EP technical specifications, attributes, parameters and parts with similar specifications to Analog Devices Inc. AMP02EP.
- Mounting TypeThrough Hole
- Package / Case8-DIP (0.300, 7.62mm)
- Surface MountNO
- Operating Temperature-40°C~85°C
- PackagingTube
- JESD-609 Codee0
- Pbfree Codeno
- Part StatusObsolete
- Moisture Sensitivity Level (MSL)3 (168 Hours)
- Number of Terminations8
- Terminal FinishTIN LEAD
- Terminal PositionDUAL
- Peak Reflow Temperature (Cel)NOT SPECIFIED
- Number of Functions1
- Supply Voltage15V
- Terminal Pitch2.54mm
- Reach Compliance Codeunknown
- Time@Peak Reflow Temperature-Max (s)NOT SPECIFIED
- Pin Count8
- JESD-30 CodeR-PDIP-T8
- Qualification StatusCOMMERCIAL
- Number of Circuits1
- Current - Supply5mA
- Slew Rate6V/μs
- Amplifier TypeInstrumentation
- Current - Input Bias2nA
- Voltage - Supply, Single/Dual (±)±4.5V~18V
- Neg Supply Voltage-Nom (Vsup)-15V
- Voltage - Input Offset20μV
- Current - Output / Channel32mA
- 3db Bandwidth1.2MHz
- Input Offset Current-Max (IIO)0.005μA
- Voltage Gain-Min1
- Common-mode Reject Ratio-Min75 dB
- Voltage Gain-Nom10
- Length9.27mm
- Height Seated (Max)4.57mm
- RoHS StatusNon-RoHS Compliant
AMP02EP Overview
It is packaged in an 8-DIP (0.300, 7.62mm)-case that protects the operational amplifiers from damage. An op amp of this type is a Instrumentation-type. As far as the packaging is concerned, buffer op amp is delivered in a Tube case. It is estimated that there will be at least 8 terminations this year. A total of 8 pins are attached to buffer op amp. As a reminder, this buffer op amp should be powered by 15V battery and that the battery should be inserted in the amplifier. This electronic part is recommended for mounting type Through Hole. In terms of operating temperature, this instrumentation amplifier is well suited to a temperature range of -40°C~85°C. This op amp ic has 1 circuits. For optimal performance, this electrical part should be connected to a supply with a current of 5mA. This op amp ic can conduct a minimum voltage gain of 1.
AMP02EP Features
8 Pins
supply voltage of 15V
AMP02EP Applications
There are a lot of Rochester Electronics, LLC
AMP02EP Instrumentational OP Amps applications.
Logarithmic operation circuits
Exponential operation circuits
Multiplication circuits
Division circuits
Precision measurement
Power control
Information processing
Weak signal detection
Signal amplification
Signal filtering
It is packaged in an 8-DIP (0.300, 7.62mm)-case that protects the operational amplifiers from damage. An op amp of this type is a Instrumentation-type. As far as the packaging is concerned, buffer op amp is delivered in a Tube case. It is estimated that there will be at least 8 terminations this year. A total of 8 pins are attached to buffer op amp. As a reminder, this buffer op amp should be powered by 15V battery and that the battery should be inserted in the amplifier. This electronic part is recommended for mounting type Through Hole. In terms of operating temperature, this instrumentation amplifier is well suited to a temperature range of -40°C~85°C. This op amp ic has 1 circuits. For optimal performance, this electrical part should be connected to a supply with a current of 5mA. This op amp ic can conduct a minimum voltage gain of 1.
AMP02EP Features
8 Pins
supply voltage of 15V
AMP02EP Applications
There are a lot of Rochester Electronics, LLC
AMP02EP Instrumentational OP Amps applications.
Logarithmic operation circuits
Exponential operation circuits
Multiplication circuits
Division circuits
Precision measurement
Power control
Information processing
Weak signal detection
Signal amplification
Signal filtering
AMP02EP More Descriptions
Amplifier, High Accuracy; Instrumentation; /-4.5 to /-18V; 5mA; 200kHz; 8 Lead PDIP
Non-RoHS Compliant R-PDIP-T8 TIN LEAD Tube op amp amplifier circuit 9.27mm 2nA -15V 1.2MHz
Instrumentation Amplifier, 1 Func, 200uV Offset-Max, 1.2MHz Band Width, PDIP8
The AMP-02 is the first precision instrumentation amplifier available in an 8-pin package. Gain of the AMP-02 is set by a single external resistor, and can range from 1 to 10,000. No gain set resistor is required for unity gain. The AMP-02 includes an input protection network that allows the inputs to be taken 60V beyond either supply rail without damaging the device. Laser trimming reduces the input offset voltage to under 100 µV. Output offset voltage is below 4 mV and gain accuracy is better than 0.5% for gain of 1000. PMI's proprietary thin-film resistor process keeps the gain temperature coefficient under 50 ppm/°C. Due to the AMP-02's design, its bandwidth remains very high over a wide range of gain. Slew rate is over 4V/µS making the AMP-02 ideal for fast data acquisition systems. A reference pin is provided to allow the output to be referenced to an external DC level. This pin may be used for offset correction or level shifting as required. In the 8-pin package, sense is internally connected to the output. For an instrumentation amplifier with the highest precision, consult the AMP-01 data sheet.
Non-RoHS Compliant R-PDIP-T8 TIN LEAD Tube op amp amplifier circuit 9.27mm 2nA -15V 1.2MHz
Instrumentation Amplifier, 1 Func, 200uV Offset-Max, 1.2MHz Band Width, PDIP8
The AMP-02 is the first precision instrumentation amplifier available in an 8-pin package. Gain of the AMP-02 is set by a single external resistor, and can range from 1 to 10,000. No gain set resistor is required for unity gain. The AMP-02 includes an input protection network that allows the inputs to be taken 60V beyond either supply rail without damaging the device. Laser trimming reduces the input offset voltage to under 100 µV. Output offset voltage is below 4 mV and gain accuracy is better than 0.5% for gain of 1000. PMI's proprietary thin-film resistor process keeps the gain temperature coefficient under 50 ppm/°C. Due to the AMP-02's design, its bandwidth remains very high over a wide range of gain. Slew rate is over 4V/µS making the AMP-02 ideal for fast data acquisition systems. A reference pin is provided to allow the output to be referenced to an external DC level. This pin may be used for offset correction or level shifting as required. In the 8-pin package, sense is internally connected to the output. For an instrumentation amplifier with the highest precision, consult the AMP-01 data sheet.
The three parts on the right have similar specifications to AMP02EP.
-
ImagePart NumberManufacturerMounting TypePackage / CaseSurface MountOperating TemperaturePackagingJESD-609 CodePbfree CodePart StatusMoisture Sensitivity Level (MSL)Number of TerminationsTerminal FinishTerminal PositionPeak Reflow Temperature (Cel)Number of FunctionsSupply VoltageTerminal PitchReach Compliance CodeTime@Peak Reflow Temperature-Max (s)Pin CountJESD-30 CodeQualification StatusNumber of CircuitsCurrent - SupplySlew RateAmplifier TypeCurrent - Input BiasVoltage - Supply, Single/Dual (±)Neg Supply Voltage-Nom (Vsup)Voltage - Input OffsetCurrent - Output / Channel3db BandwidthInput Offset Current-Max (IIO)Voltage Gain-MinCommon-mode Reject Ratio-MinVoltage Gain-NomLengthHeight Seated (Max)RoHS StatusContact PlatingMountNumber of PinsECCN CodeResistanceTerminal FormBase Part NumberNumber of ElementsOperating Supply CurrentSupply Current-MaxCommon Mode Rejection RatioOutput Current per ChannelInput Offset Voltage (Vos)Voltage GainAverage Bias Current-Max (IIB)Power Supply Rejection Ratio (PSRR)Radiation HardeningLead FreeFactory Lead TimeLifecycle StatusTerminationOperating Supply VoltageNumber of ChannelsNominal Supply CurrentMax Supply CurrentBandwidthGain Bandwidth ProductDual Supply VoltageHeightWidthREACH SVHCTechnologyMax Input VoltageNon-linearity-MaxView Compare
-
AMP02EPThrough Hole8-DIP (0.300, 7.62mm)NO-40°C~85°CTubee0noObsolete3 (168 Hours)8TIN LEADDUALNOT SPECIFIED115V2.54mmunknownNOT SPECIFIED8R-PDIP-T8COMMERCIAL15mA6V/μsInstrumentation2nA±4.5V~18V-15V20μV32mA1.2MHz0.005μA175 dB109.27mm4.57mmNon-RoHS Compliant-----------------------------------
-
Surface Mount16-SOIC (0.295, 7.50mm Width)--40°C~85°CTubee0noObsolete1 (Unlimited)16-DUAL240115V--3016----6V/μsInstrumentation4nA±4.5V~18V-15V40μV-1.2MHz---10-2.65mmNon-RoHS CompliantLead, TinSurface Mount16EAR9916.5GOhmGULL WINGAMP0215mA6mA115 dB32mA200μV80dB0.02μA75dBNoContains Lead----------------
-
Through Hole8-DIP (0.300, 7.62mm)--40°C~85°CTubee3noActive1 (Unlimited)8Matte Tin (Sn)DUAL-115V2.54mm--8----6V/μsInstrumentation4nA±4.5V~18V-15V-32mA1.2MHz---109.27mm-ROHS3 Compliant-Through Hole8EAR9916.5GOhm-AMP02-6mA-115 dB22mA40μV80dB0.02μA75dBNoContains Lead10 WeeksPRODUCTION (Last Updated: 3 weeks ago)Through Hole18V15mA6mA1.2MHz1.2MHz9V4.57mm7.24mmNo SVHC---
-
Through Hole18-CDIP (0.300, 7.62mm)--55°C~125°CTubee0noActive1 (Unlimited)18Tin/Lead (Sn63Pb37)DUAL-115V2.54mm--18----4.5V/μsInstrumentation1nA±4.5V~18V-15V20μV-0.57MHz---1000024.38mm-Non-RoHS CompliantLead, TinThrough Hole18EAR9920GOhm-AMP0114.8mA-95 dB120mA100V80dB--NoContains Lead10 WeeksPRODUCTION (Last Updated: 1 month ago)---3mA4.8mA570 kHz26MHz15V4.93mm7.87mm-BIPOLAR18V0.005%
Popular Search Part Number
Related Keywords
Search Tags
Latest News
-
19 February 2024
SG3525AN Controller: Specifications, Application Circuit and Other Details
Ⅰ. Overview of SG3525ANⅡ. Specifications of SG3525ANⅢ. Application circuit of SG3525ANⅣ. How to evaluate the efficiency of SG3525AN controller?Ⅴ. Recommended operating conditions for SG3525ANⅥ. What are the advantages... -
19 February 2024
SS14 Schottky Power Diode Function, Applications, Working Principle and Features
Ⅰ. What is a Schottky diode?Ⅱ. SS14 overviewⅢ. Common brands of SS14 diodeⅣ. Typical performance characteristics of SS14 diodeⅤ. The function of SS14 diodeⅥ. What are the applications... -
20 February 2024
LM358DR2G Operational Amplifier Symbol, Features, Applications and More
Ⅰ. Introduction to LM358DR2GⅡ. Technical parameters of LM358DR2GⅢ. Features of LM358DR2GⅣ. Symbol, footprint and pin configuration of LM358DR2GⅤ. Where is LM358DR2G used?Ⅵ. Circuit description of LM358DR2GⅦ. The difference... -
20 February 2024
MB6S Rectifier Bridge Specifications, Working Principle and Features
Ⅰ. Overview of MB6SⅡ. Specifications of MB6SⅢ. Working principle of MB6SⅣ. Circuit schematic diagram of MB6SⅤ. What are the features of MB6S?Ⅵ. Absolute maximum ratings of MB6SⅦ. How...
Help you to save your cost and time.
Reliable package for your goods.
Fast Reliable Delivery to save time.
Quality premium after-sale service.